Putting my e36 M3 up for sale as I have a line on its replacement. Purchased in April 2016 with 185k miles on chassis and have slowly stripped it down into the track car that it sits as today.
Body currently has 192k miles on it.
Head was pulled and refreshed at 185k miles.
Mostly track miles have been put on the car since 2016
Mid Ohio/High Plains Raceway
Runs 1:44's Club Course at Mid Ohio in my incapable hands.
Asking $15,000 OBO
Picture link
Below is a list of parts/ work done, I am sure I am missing some, I have turned just about every nut and bolt on this car. Fun as hell/feels like a go cart on track and is predictable and toss able into corners.
EXTERIOR:
Active Autowerke's 3" race exhaust
Shorty Headers
Motion Motorsport Under panel with radiator baffle
Carbon sunroof delete
INTERIOR:
Traqmate GPS Data System
Clownshoe Motorsport Logger S E36 CAN Data Logger
Corbeau FX1 Pro's
Racetech 6 point harnesses
Kirk roll bar
Motion Motorsport seat mounts
Bimmerworld Floor mount adapters
AKG shifter
SUSPENSION, WHEELS, & BRAKES:
D Force LTW5's with NT01's
Fortune Auto 500 series coil overs
Turner Front Sway Bar
Bimmerworld Race Studs
DTC60's
New wheel bearings all 4 corners
Caliper rebuild with brass guides
Welded in AKG subframe reinforcements
DRIVETRAIN:
Head pulled/refreshed
Drive shaft replaced
Rear end new seals/ AKG reinforcement plates
Oil pump/pickup replaced
Oil pump nut
UUC Flywheel
M50 manifold
AKG bushings throughout
Complete cooling system replacement
Left to do:
Wideband bung installed with exhaust (Zeitronix) needs connected to Gauge
Oil pan baffle
Surface rust around trunk/taillight
Surface rust on rear fenders (cleaned and painted because race car)
Spares:
Bimmerworld oil baffle
E36 LTW Wing
Spare pads
Misc. parts​
Body currently has 192k miles on it.
Head was pulled and refreshed at 185k miles.
Mostly track miles have been put on the car since 2016
Mid Ohio/High Plains Raceway
Runs 1:44's Club Course at Mid Ohio in my incapable hands.
Asking $15,000 OBO
Picture link
Below is a list of parts/ work done, I am sure I am missing some, I have turned just about every nut and bolt on this car. Fun as hell/feels like a go cart on track and is predictable and toss able into corners.
EXTERIOR:
Active Autowerke's 3" race exhaust
Shorty Headers
Motion Motorsport Under panel with radiator baffle
Carbon sunroof delete
INTERIOR:
Traqmate GPS Data System
Clownshoe Motorsport Logger S E36 CAN Data Logger
Corbeau FX1 Pro's
Racetech 6 point harnesses
Kirk roll bar
Motion Motorsport seat mounts
Bimmerworld Floor mount adapters
AKG shifter
SUSPENSION, WHEELS, & BRAKES:
D Force LTW5's with NT01's
Fortune Auto 500 series coil overs
Turner Front Sway Bar
Bimmerworld Race Studs
DTC60's
New wheel bearings all 4 corners
Caliper rebuild with brass guides
Welded in AKG subframe reinforcements
DRIVETRAIN:
Head pulled/refreshed
Drive shaft replaced
Rear end new seals/ AKG reinforcement plates
Oil pump/pickup replaced
Oil pump nut
UUC Flywheel
M50 manifold
AKG bushings throughout
Complete cooling system replacement
Left to do:
Wideband bung installed with exhaust (Zeitronix) needs connected to Gauge
Oil pan baffle
Surface rust around trunk/taillight
Surface rust on rear fenders (cleaned and painted because race car)
Spares:
Bimmerworld oil baffle
E36 LTW Wing
Spare pads
Misc. parts​
Comment