Announcement

Collapse
No announcement yet.

Overheating on track only

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • O'Neill
    replied
    Wasn't your car remapped some time ago? has the ecu been put back to oem/maybe try another ecu if your new parts don't solve the problem.

    Or oil cooler and mishimoto rad.

    Leave a comment:


  • shimmy
    replied
    Originally posted by alexk View Post
    Well.
    Very hot day, tight track, most corners with 2nd gear, oil temp at about 120C and then water temp almost reached red (it touched red).
    I backed off a lot and it cooled down.

    As you saw in my post for the thermostat tests, it was obvious that my stat didn't open fully so the water flow was not maximum.
    I am not running any cats, just a backbox.
    Might be a strange fact, but I doubt the engine runs lean when the consumption on track is > 26lt / 100km.

    Shimmy.
    I have a question for you.
    Are you using the original BMW coolant fluid and is it mixed with water or not ?
    i have whatever bmw put in with. new engine, not sure what

    Leave a comment:


  • alexk
    replied
    Originally posted by shimmy View Post
    Alex, remind me when your overheating happened (did it meet the criteria I pointed out above)
    Well.
    Very hot day, tight track, most corners with 2nd gear, oil temp at about 120C and then water temp almost reached red (it touched red).
    I backed off a lot and it cooled down.

    As you saw in my post for the thermostat tests, it was obvious that my stat didn't open fully so the water flow was not maximum.
    I am not running any cats, just a backbox.
    Might be a strange fact, but I doubt the engine runs lean when the consumption on track is > 26lt / 100km.

    Shimmy.
    I have a question for you.
    Are you using the original BMW coolant fluid and is it mixed with water or not ?

    Leave a comment:


  • shimmy
    replied
    Originally posted by thegingerninja View Post
    Sometimes when the internal coolant system reaches 7 or 8 years old there can be a thin layer of corrosion across the entire internal surface area. If the water temp reaches boiling point you can get "kettling" (small gas bubbles) forming on this line layer of corrosion. Obviously the air bubbles act as an insulator and the temp will increase if you don't drop the engine load.

    I think there are some products you can run through the coolant system to remove the layer, and then refill using an additive which combats the kettling. I had a problem like this on a race car and I tried a product called water wetter - I wasn't convinced it would work, but I saw a drop in coolant temps afterwards, probably about 10 degrees.

    I have spoken with some other csl owners who have experienced what you describe shimmy, particularly climbing the hill at the ring. We ruled out a failing viscous fan because of the sustained high speed would create plenty of air flow. The other possibilities were: radiator had lost it's heat capacity due to ageing, water pump lost efficiency or engine running lean (due to fuel supply not meeting demand at full throttle and high revs).

    Only way to find out for sure is to rule them out one at a time.

    great post, thanks

    my oil and water coolant system is new as is engine. water rad i have not renewed yet but have cleaned and straightened fins.

    water pump is new as is sensors and stats as well as wetter used.

    def not fan as you say

    my thoughts now are 100 cell cat affecting ecu at full throttle or fuel system running it just lean at full throttle

    i have trief another fuel pump (no change) and now have just changed fuel regulator and filter. regulator does change fueling at full throttle so maybe that it, well soon see

    Leave a comment:


  • thegingerninja
    replied
    Sometimes when the internal coolant system reaches 7 or 8 years old there can be a thin layer of corrosion across the entire internal surface area. If the water temp reaches boiling point you can get "kettling" (small gas bubbles) forming on this line layer of corrosion. Obviously the air bubbles act as an insulator and the temp will increase if you don't drop the engine load.

    I think there are some products you can run through the coolant system to remove the layer, and then refill using an additive which combats the kettling. I had a problem like this on a race car and I tried a product called water wetter - I wasn't convinced it would work, but I saw a drop in coolant temps afterwards, probably about 10 degrees.

    I have spoken with some other csl owners who have experienced what you describe shimmy, particularly climbing the hill at the ring. We ruled out a failing viscous fan because of the sustained high speed would create plenty of air flow. The other possibilities were: radiator had lost it's heat capacity due to ageing, water pump lost efficiency or engine running lean (due to fuel supply not meeting demand at full throttle and high revs).

    Only way to find out for sure is to rule them out one at a time.

    Leave a comment:


  • shimmy
    replied
    Originally posted by maxmeerkat View Post
    I guess next step is a race bonnet from Geoff Steele
    maybe but not to cure this, it is something much more fundamental than that

    Leave a comment:


  • maxmeerkat
    replied
    I guess next step is a race bonnet from Geoff Steele

    Leave a comment:


  • shimmy
    replied
    Originally posted by alexk View Post
    shimmy

    My problem was faulty thermostat and fan coupling.

    thank you please
    Alex, remind me when your overheating happened (did it meet the criteria I pointed out above)


    Originally posted by maxmeerkat View Post
    If your water temps are rising, have you considered the bmw motorsport thermostat ? Will be fitting mine soon.
    Put in new stat then Motorsport stat. Does not make any difference to this as it is at hot conditions when any stat will be fully open

    Leave a comment:


  • maxmeerkat
    replied
    If your water temps are rising, have you considered the bmw motorsport thermostat ? Will be fitting mine soon.

    Leave a comment:


  • alexk
    replied
    shimmy

    My problem was faulty thermostat and fan coupling.

    thank you please

    Leave a comment:


  • 3wheels3
    replied
    Have voted but to confirm in txt...no mods & no over heating. Water temp rock solid. Always make sure oil temp is around road temp returning to pits.

    Leave a comment:


  • glendog74
    replied
    Originally posted by CraigMillwardCroft View Post
    I was at Circuit de Bretange last year temp around 28 degrees, and oil temp went to 125 but water no problem, does this help my oil temp when on track rises to 125 all tracks. :thumbs:
    Originally posted by Funkster View Post
    As been said already, oil up to 125 but water temp rock solid in the middle.

    That's on my old engine and the new one !:-D

    With standard cats but SS middle and back.
    As above for me Shim:

    Oil temps rise on mine during high ambient temps (to approx 125) but I have yet to see my water temps rise...

    SS headers/200 cell OEM cats/SS centre/SS back box

    :smokin:

    Leave a comment:


  • Funkster
    replied
    As been said already, oil up to 125 but water temp rock solid in the middle.

    That's on my old engine and the new one !:-D

    With standard cats but SS middle and back.

    Leave a comment:


  • shimmy
    replied
    Originally posted by lawsy View Post
    Have you fitted your pump/reg yet?

    You got text BTW:thumbs:
    Yep fitted and ready to try it:-D

    Leave a comment:


  • shane@mbtech
    replied
    Have you fitted your pump/reg yet?

    You got text BTW:thumbs:

    Leave a comment:

Working...
X