Announcement

Collapse
No announcement yet.

Alcon Conversion Front Wheel bell. Where from??

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Johnnywb
    replied
    Originally posted by KPNUTZ View Post
    Need to check my calipers as I'm sure my bleed nipple is pointing upwards!

    As a side note, can only speak highly of Dave at Ears, haven't dealt with him since I had my Evos, top bloke.
    The bleed nipple should be pointing up to let the air out.

    Basically some muppet put my calipers together the wrong way once they were painted... THe smaller of the three (6) pistons should be at the bottom, you can see on mine, it's at the top...

    Nervous wait for parts delivery today....

    Leave a comment:


  • KPNUTZ
    replied
    Need to check my calipers as I'm sure my bleed nipple is pointing upwards!

    As a side note, can only speak highly of Dave at Ears, haven't dealt with him since I had my Evos, top bloke.

    Leave a comment:


  • Johnnywb
    replied
    Ok, latest update;

    Alcon never called back.

    Dave at Ears on the other hand, could not have been more helpful.

    It would seem that my car isn't the first CSL he's seen with this problem and he has been working on a fix. He did explain the issue to me, but i'm hard of thinking.

    From memory, i think (and i'm sure someone will be able to confirm), the alloy used for the front bell housings basically isn't strong enough and degrades over time. Dave has been working with an engineer to come up with a better solution.

    He's sent down a couple of bell housings, bobbins and other bits.

    Essentially i've opted to turn the fronts into a full floating set up in line with the race set up.

    I'll let you know how we get on.

    I'll also see if i can get Dave to post here exactly what's going on as he's got a much better idea than i!

    Leave a comment:


  • Johnnywb
    replied
    Thanks all.

    I've spoken to Alcon this morning who are going to have a look into sourcing something.

    The guy i spoke to thought that the items were custom made for the CSL, in which case it might be a hassle to get something.

    Will let you know how it pans out.

    Leave a comment:


  • shane@mbtech
    replied
    To me it looks like wheel acid/chemical has been used to clean the wheels and and the bell has reacted/oxidised and thats why they have gone this way?

    That and the bolts holding the disc to the bell have been overtightened.

    Leave a comment:


  • leaded
    replied
    Give Dave a call at Ears motorsport. 01625 433773

    [email protected]

    They do Alcon stuff and are very helpful.

    Leave a comment:


  • chicken
    replied
    what ever happened to good workmanship or at least pride? :banghead:

    Leave a comment:


  • M5 Powered
    replied
    Hi Johnny,

    That is pretty shocking. Those don't seem to be original Bells. The correct ones are as NZ shows (they have a black heat coating on them).

    Call Alcon in the morning. Customer service was excellent!

    Leave a comment:


  • NZ_M3
    replied
    Originally posted by lawsy View Post
    My guess is when they were painted yellow, and the decals applied, the nipples and connecting pipes were installed incorrectly.
    Lawsy's correct - your calipers are upside down and as stated the bleed nipple and the connecting pipes were installed incorrectly.

    That wear mark looks to me like one of the brake pads have failed and come away from the holding slot within the caliper and made contact with the disc and chewed through it.

    You can buy the bells independently from Alcon - if you search I am sure someone has posted a part number up before, otherwise I can look for it later on.



    I think this is the correct bell part number (found it in my photo files)

    Leave a comment:


  • AlexGTT
    replied
    That is diabolical workmanship! Can't believe anyone would do that in a professional workshop..................but then again I shouldn't be shocked. The disc's look ready to part from the hubs on the first big brake at the end of Kemel! Glad you didn't get there with them in that state!:bigcry:

    Leave a comment:


  • shane@mbtech
    replied
    They have been made like that.

    If you swapped sides and turned them the correct way, your bleed nipples would then be at the bottom. And bleeding from the bottom of the caliper would be difficult.So you will need to take bleed nipples out, and take connecting pipe off, then swap them top to bottom.

    My guess is when they were painted yellow, and the decals applied, the nipples and connecting pipes were installed incorrectly.

    Leave a comment:


  • shane@mbtech
    replied
    Originally posted by Johnnywb View Post
    My plan is to call Alcon in the morning. The work was done by Thorney originally (at least the brakes were supplied by them as there's a receipt for it, it's in the car so will need to check whether it included fitting).

    How the F.ck could someone install the calipers on the wrong side?! Can't say i've noticed a big problem, but then again...
    The leading piston on the direction of disc travel, should be the smaller piston. So it grabs the brakes gradually. They way yours are installed means the biggest piston is braking first, so is rendering the smaller ones a little redundant. :thumbs:

    Leave a comment:


  • Johnnywb
    replied
    Originally posted by lawsy View Post
    Your calipers are on the the wrong side too, you will have been experiencing brake issues, overheating?

    Give alcon a call, and tell them which kit you have, they may have some lying about.
    My plan is to call Alcon in the morning. The work was done by Thorney originally (at least the brakes were supplied by them as there's a receipt for it, it's in the car so will need to check whether it included fitting).

    How the F.ck could someone install the calipers on the wrong side?! Can't say i've noticed a big problem, but then again...

    Leave a comment:


  • shane@mbtech
    replied
    Your calipers are on the the wrong side too, you will have been experiencing brake issues, overheating?

    Give alcon a call, and tell them which kit you have, they may have some lying about.

    Leave a comment:


  • shimmy
    replied
    Ouch, silly billy whomever it was.

    Leave a comment:

Working...
X