my M3 CSL

[monkeycsl]

Does ac still work ok??

[CraigMillwardCroft]

Neat looking job :thumbs:

[alexk]

Does ac still work ok??

Yes - no problems.

[alexk]

One more performance update.

I bought a set of titanium wheel bolts.
They were discounted and I could not resist.

The BBS wheel bolts are 388g while the titanium ones are 173g.
This is a 215g difference.

[glendog74]

Nice :thumbs:

[Mike RT4]

Nice mods .

I did the titanium stud and nut kit, as it makes swapping wheels over a little easier .

[alexk]

conrod bearings

A long overdue post as I did this work back in April...
I was getting the car ready to do a trackday at the Ring, but then I decided to take the M5 instead as it was raining.

I had decided to replace the conrod bearings as proactive maintenance.
The car had 112800 km. Now it has 115k km and still runs strong.

I started by removing the front subframe.



I bought from Ebay the tool to hold the engine.



But before we continue, check these original BMW workshop tools my brother got me :thumbs:



This one is to fill in oil in gearboxes / differentials and its very precise and you can use all the oil without wasting any of it.




Here we can see the mighty crankshaft.
The engine is super clean inside. The 3k km oil changes are the reason behind it :whistle:



I know what you are thinking, why is the crankshaft blue / purple ?
Don't worry, it's normal for some of these as they were heat treated from the factory.



The bearings were not too bad, but not too great either.
I think timing was good.



In more detail

#1


#2


#3


#4


#5


#6


While doing all this work, I changed the leaking steering rack hose



And the engine mounts - look the difference !



And did the valve clearance again. Only 1 valve was slightly off :thumbs:



Also, I changed the sparkplugs and the coil packs - also proactive maintenance.

All this was great but then I thought, it's good if I do this modification I always wanted to do.

Some carbon scavenged by a crashed Lamborghini GT3 racecar in Hockenheim.
The aluminium bolt is from a N54 engine.... because CSLs are meant to be light.



Here with the oil catch tank.



And mounted. The hoses are nice silicon ones.



The catch tank works great.

[0-60motorsports]

A long overdue post as I did this work back in April...
I was getting the car ready to do a trackday at the Ring, but then I decided to take the M5 instead as it was raining.

I had decided to replace the conrod bearings as proactive maintenance.
The car had 112800 km. Now it has 115k km and still runs strong.

I started by removing the front subframe.



I bought from Ebay the tool to hold the engine.



But before we continue, check these original BMW workshop tools my brother got me :thumbs:



This one is to fill in oil in gearboxes / differentials and its very precise and you can use all the oil without wasting any of it.




Here we can see the mighty crankshaft.
The engine is super clean inside. The 3k km oil changes are the reason behind it :whistle:



I know what you are thinking, why is the crankshaft blue / purple ?
Don't worry, it's normal for some of these as they were heat treated from the factory.



The bearings were not too bad, but not too great either.
I think timing was good.



In more detail

#1


#2


#3


#4


#5


#6


While doing all this work, I changed the leaking steering rack hose



And the engine mounts - look the difference !



And did the valve clearance again. Only 1 valve was slightly off :thumbs:



Also, I changed the sparkplugs and the coil packs - also proactive maintenance.

All this was great but then I thought, it's good if I do this modification I always wanted to do.

Some carbon scavenged by a crashed Lamborghini GT3 racecar in Hockenheim.
The aluminium bolt is from a N54 engine.... because CSLs are meant to be light.



Here with the oil catch tank.



And mounted. The hoses are nice silicon ones.



The catch tank works great.

Excellent work! Those bearings were close mate lol. I do 5k Km oil changes

[Chad]

I was thinking the bearings Didn’t look to bad ,, were they the original. Or the king race as in the photo the first coating looks black like the king race. The original are more grey from memory ,, saying that mine were down to the copper colour on a few ,, at 65k miles ,, new shells can’t hurt :thumbs: always seems to be the upper shell that get most abuse

[alexk]

I was thinking the bearings Didn’t look to bad ,, were they the original. Or the king race as in the photo the first coating looks black like the king race. The original are more grey from memory ,, saying that mine were down to the copper colour on a few ,, at 65k miles ,, new shells can’t hurt :thumbs: always seems to be the upper shell that get most abuse

No they are the original ones.
I refitted original bearings and bolts.

The left ones are the bottom ones and as you can see on mine they are worse than the top ones.

[alexk]

A recent video from a dyno test

https://www.youtube.com/watch?v=o7pihEJ5aao

[0-60motorsports]

Not bad at all! Should make some more on fresh 98/99

[alexk]

Not bad at all! Should make some more on fresh 98/99

Yes exactly :thumbs:

[rstoughy]

Nice :thumbs:

Still cant beat the induction note of a CSL :smokin:

[DazBlackCSL]

Nice Al :thumbs: