Carbon Splitters Refurb

[0836whimper]

Hi all,

In this month's Evo, Harry reports on finding using T-cut colorfast ultimate black effective in getting the carbon splitters on his Zonda back to a point where stone chips look almost invisible.

Anyone tried this or any other similar product on the carbon splitters on a CSL ?

ta,

Mark

[shimmy]

M5 Powered, after putting some miles on the splitters since the refurb how are the holding up?

Shimmy same to you?

Probably get mine done in the next couple of months.

Did mine at Finishline........won't do again! Peeling:banghead:

[billyboysm3]

Finally got round to picking up my splitters which were refurbed by Perkins.

The result? For 85 quid they look new. I can't even see where the stone chips were! Pics to follow. :thumbs:

M5 Powered have you got any picts?

[M5 Powered]

Still as new! :thumbs:

[billyboysm3]

Finally got round to picking up my splitters which were refurbed by Perkins.

The result? For 85 quid they look new. I can't even see where the stone chips were! Pics to follow. :thumbs:

M5 Powered, after putting some miles on the splitters since the refurb how are the holding up?

Shimmy same to you?

Probably get mine done in the next couple of months.

[karbonkid]

Alex, you said you used Rattle cans, where did you get them? Online or local? A local Motor factor can get our SG made up in Aerosols but I'm concerned as to the match. I also found some on Ebay, WA08 is it? Comes in two cans, £20 for the paint and the lacquer.

Thanks in advance, Baz

Got the cans at my local Autoshop off the shelf luckily.
As far as colour match goes, any A08 should match up regardless of makes, simply due to standard mix ratios being identical. Colour match will appear slightly different until lacquer is applied thou.

Alex, any first hand experience of this guy mate?

I haven't Dan but I have seen and heard his work is brill! :thumbs:

http://www.streetfire.net/video/nur-motorsport-carbonfibre-r34-rsr_637028.htm

[sailorbaz]

A08 - Silber grau

Thanks Robert. It is Sunday after all, :hahaha:

[Dan]

A08 - Silber grau

You're up early!

[Dan]

Afraid not no, never dealt with them before.

For peps in Reading area theres a good chap, Noel @ NUR-Motorsport . He manufactures carbon parts/ Repairs.

Alex, any first hand experience of this guy mate?

[glendog74]

A08 - Silber grau

[sailorbaz]

Alex, you said you used Rattle cans, where did you get them? Online or local? A local Motor factor can get our SG made up in Aerosols but I'm concerned as to the match. I also found some on Ebay, WA08 is it? Comes in two cans, £20 for the paint and the lacquer.

Thanks in advance, Baz

[s.mac]

Alex, bumper looks mint ! i like to do a bit of diy but that is going some :thumbs:

[M5 Powered]

Finally got round to picking up my splitters which were refurbed by Perkins.

The result? For 85 quid they look new. I can't even see where the stone chips were! Pics to follow. :thumbs:

[karbonkid]

:thumbs::thumbs: Superb work on the bumper Alex ... time to open your own repair shop me thinks :hahaha::hahaha::hahaha:

Back off! Me not doing another fooker!! :hahaha:

Ta thou, I was well impressed with the results from just a series of aerosols. So much so I rewound time so I could take pics of prep stages so you lot can ave a go. :hahaha: :thumbs:

[NZ_M3]

:thumbs::thumbs: Superb work on the bumper Alex ... time to open your own repair shop me thinks :hahaha::hahaha::hahaha: