Announcement

Collapse
No announcement yet.

Thank you Mike!

Collapse
X
Collapse
 
  • Page of 2
  • Filter
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
    #16
    Originally posted by Has csl View Post
    Where do I get one from? Is it from that chap, Marv968?
    And SSS, I thought you was looking for a Cecil. Did you bag one? Seen as you fitted the centre bit on a car?
    Check these posts out - gives you all the information you crave :
    Exciting carbon news! - NA M3 Forums
    https://nam3forum.com/forums/forum/csl-register/csl-register-main-discussion-centre/450547-exciting-carbon-news
    Given my car is off the road waiting for the cams from BMW (a wait which has been on-going since the end of July :banghead: ), I thought I would take the opportunity to get my guy to do some more carbon bits, so the Vorsteiner front splitter is going to be replicated (but in proper 1 x 1 pre-preg carbon and not the shonky


    CSL flippers - originals -v- current ones - NA M3 Forums
    https://nam3forum.com/forums/forum/csl-register/csl-register-main-discussion-centre/449430-csl-flippers-originals-v-current-ones
    EDITED TO CLARIFY, THE ONES IN THE FORE-GROUND ARE THE ORIGINALS AND THE ONES IN THE BACK-GROUND ARE THE NEW ONES (the creamy coloured stuff on the OE ones is where they have had the mold taken from them). Not sure where to put this, so thought I would start here and then if Mark feels it belongs in the for sale section, it

    Comment

      #17
      Originally posted by Mike R View Post
      Check these posts out - gives you all the information you crave :
      Exciting carbon news! - NA M3 Forums
      https://nam3forum.com/forums/forum/csl-register/csl-register-main-discussion-centre/450547-exciting-carbon-news
      Given my car is off the road waiting for the cams from BMW (a wait which has been on-going since the end of July :banghead: ), I thought I would take the opportunity to get my guy to do some more carbon bits, so the Vorsteiner front splitter is going to be replicated (but in proper 1 x 1 pre-preg carbon and not the shonky


      https://nam3forum.com/forums/forum/c...v-current-ones
      Thanks mate:thumbs:

      Comment

        #18
        Took another pic while the sun was shining!



        Has csl - sorry for not replying to your PM, by the time I saw it I'd already seen you'd been pointed in the right direction in this thread

        Comment

          #19
          Originally posted by Marv968 View Post
          Took another pic while the sun was shining!



          Has csl - sorry for not replying to your PM, by the time I saw it I'd already seen you'd been pointed in the right direction in this thread
          That looks superb! How difficult are these to fit?

          Comment

            #20
            Originally posted by Marv968 View Post
            Took another pic while the sun was shining!



            Has csl - sorry for not replying to your PM, by the time I saw it I'd already seen you'd been pointed in the right direction in this thread
            That's ok mate. And that looks spot on. Shame BMW didn't do this from factory.

            Comment

              #21
              What other carbon parts do you do Mike?

              Comment

                #22
                Originally posted by SANJ View Post
                That looks superb! How difficult are these to fit?
                Easy peasy.

                The whole rear seat bottom just pulls out as one peice, there's a couple of plastic rivets to battle with on the underside (they will pull off with a decent amount of force) and a metal pin...that's about it!

                Comment

                Previous 1 2 template Next
                Working...
                X