Announcement

Collapse
No announcement yet.

What could cause my engine to seize?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • jayjaya29
    replied
    The clutch works if you install it with the spring pack facing the the flywheel. This is a proven combo used on thousands of cars.

    The clutch is actually from an E34 M5, not an E39.
    Last edited by jayjaya29; 08-07-2025, 01:52 PM.

    Leave a comment:


  • Darbshaw
    replied
    I understand, but why choose a wrong dimension clutch though. They just need to measure the potential new replacement clutch center hub and compare with the stock one.
    My understanding is that the E39 clutch is rated a little higher for torque/hp than the normal clutch that comes on ZF320 6 cyl cars. I haven't seen one but I'd guess the ZF320 w/ V8 bellhousing is slightly longer to compensate for this dimensional difference in clutch.

    So maybe you can get away with an "upgraded" e36/46 ZF clutch and pressure plate, but the cost effective option is to use the clutch from an E39. There also may not be good availability of uprated clutches for the 6-Cyl ZF box that are also sprung

    Leave a comment:


  • sapote
    replied
    Originally posted by jayjaya29 View Post

    This is aftermarket parts. Single mass flywheel, so you need a sprung clutch.
    I understand, but why choose a wrong dimension clutch though. They just need to measure the potential new replacement clutch center hub and compare with the stock one.

    Leave a comment:


  • bigjae46
    replied
    Originally posted by Darbshaw View Post
    Great to know. It's more the extra work that goes into it now. I also have a TIG welder, but no experience with it and no gas. It's a purchase that I need to make, but I've been avoiding it. Let alone learning to weld aluminum.

    Out of curiosity Jay, did you TIG weld yours together? I'm curious if I can get away with my flux core welder for this. I'm sure the answer is no.
    You need a spool gun but it probably won't work too well. Really need TIG on AC with Argon. The challenge will be getting the cast aluminum clean. The aluminum is somewhat porous so you have clutch material and oil in there. You can use a MAP torch to burn it all off, not sure what it does to the metal. Could strengthen it, weaken it or make it brittle...no idea.

    I repaired an oil pan which...its repaired and doesn't leak but it ain't got no dimes to stack. I'll leave it there. This job is probably worth paying someone to TIG.

    Leave a comment:


  • bigjae46
    replied
    Originally posted by jayjaya29 View Post

    This is aftermarket parts. Single mass flywheel, so you need a sprung clutch.
    Pretend I'm an idiot and that I still have no idea what you're talking about...🤣🤣🤣

    Does this involve aftermarket parts?

    Leave a comment:


  • jayjaya29
    replied
    To remove the clutch from the guide tube, I had to destroy the guide tube. You will need a new one.

    I had a buddy tig weld the squares back in but its not pretty. Cast aluminum is extremely difficult to weld because its hard to get it super clean. To weld aluminum mig you will need a spool gun, solid core aluminum wire, the correct gas, etc etc

    To be honest, epoxying in the cutouts would probably be my recommendation.

    Leave a comment:


  • Darbshaw
    replied
    Out of curiosity and saving a couple bucks. Is it possible to reuse the TOB tube and clean it up a bit? Or to prevent a future mistake just cut it a hair shorter? Or would this cause more issues since the TOB needs this length?


    I welded the 2 squares I cut out of my bellhousing back on and the trans has seen much more abuse without any negative effects.
    If you save the square that you cut out then you can just get it welded up. Shouldn’t affect strength too much. In fact, the weld is going to be stronger than the cast aluminum. The key will be to get the weld area really clean so that the heat affected zone is minimized which is what weakens the weld area.
    Great to know. It's more the extra work that goes into it now. I also have a TIG welder, but no experience with it and no gas. It's a purchase that I need to make, but I've been avoiding it. Let alone learning to weld aluminum.

    Out of curiosity Jay, did you TIG weld yours together? I'm curious if I can get away with my flux core welder for this. I'm sure the answer is no.


    Thanks again for all of the help, I would have been extremely stuck and puzzled when I tried to drop the trans without your pointers.


    Edit: Looking at this in hindsight, there was a obvious clue that something was not right. The trans was slightly pushed out/not sitting flush when I bolted it up. Once I loosended the trans again, it pushed itself out immediately.
    Last edited by Darbshaw; 08-07-2025, 10:28 AM.

    Leave a comment:


  • jayjaya29
    replied
    Originally posted by sapote View Post

    Then it’s the wrong clutch for the box.

    Why people used it?
    This is aftermarket parts. Single mass flywheel, so you need a sprung clutch.

    Leave a comment:


  • sapote
    replied
    Originally posted by jayjaya29 View Post

    The clutch is not symmetrical. The splined tube does not have equal stick out relative to the clutch friction surface. If you install it as marked on the clutch then the clutch friction welds itself to the clutch fork guide tube.
    Then it’s the wrong clutch for the box.

    Why people used it?

    Leave a comment:


  • jayjaya29
    replied
    Originally posted by bigjae46 View Post

    So what causes this?
    The clutch is not symmetrical. The splined tube does not have equal stick out relative to the clutch friction surface. If you install it as marked on the clutch then the clutch friction welds itself to the clutch fork guide tube.

    Leave a comment:


  • bigjae46
    replied
    Originally posted by jayjaya29 View Post

    OP didn't install the clutch disc backwards from the way its marked.

    Also, Sapote, you lost the bet. 😘

    I welded the 2 squares I cut out of my bellhousing back on and the trans has seen much more abuse without any negative effects.
    So what causes this?

    Leave a comment:


  • jayjaya29
    replied
    Originally posted by bigjae46 View Post
    If you save the square that you cut out then you can just get it welded up. Shouldn’t affect strength too much. In fact, the weld is going to be stronger than the cast aluminum. The key will be to get the weld area really clean so that the heat affected zone is minimized which is what weakens the weld area.

    I don’t understand how this happens? Clutch disc backwards? With me ZF320 and OEM pressure plate, I have to install an E34 M5 clutch disc backwards so the spring pack clears
    OP didn't install the clutch disc backwards from the way its marked.

    Also, Sapote, you lost the bet. 😘

    I welded the 2 squares I cut out of my bellhousing back on and the trans has seen much more abuse without any negative effects.

    Leave a comment:


  • 332
    replied
    This is what prompted me to ask you if it was a smg or manual, I have the same transmission setup on my car. ZF 5 speed, 10lb JB racing flywheel, fx400 4 puck.. proper fucked you are.
    Last edited by 332; 08-06-2025, 10:09 PM.

    Leave a comment:


  • bigjae46
    replied
    If you save the square that you cut out then you can just get it welded up. Shouldn’t affect strength too much. In fact, the weld is going to be stronger than the cast aluminum. The key will be to get the weld area really clean so that the heat affected zone is minimized which is what weakens the weld area.

    I don’t understand how this happens? Clutch disc backwards? With me ZF320 and OEM pressure plate, I have to install an E34 M5 clutch disc backwards so the spring pack clears

    Leave a comment:


  • sapote
    replied
    Wonder why Day1 it didn't weld itself with engine actually running?

    Leave a comment:

Working...
X