Originally posted by karter16
View Post
Announcement
Collapse
No announcement yet.
MSS54 DS2 Tool: FREE - DME tune, program, flash counter, codes, adaptions, etc
Collapse
X
-
I think it depends on the version of FTDI chip. The earlier cables with those chip needed a hardware mod but the later chips did not.
- Likes 1
-
Sorry been so long I would need to figure out again how to do the coding. The flap is in the CSL code and form what I remember was just a flag as on and off. Can't remember how and what was need though sorry
Leave a comment:
-
Thanks for this - I vaguely recall from a long time ago that there used to be a fix that had to be done for some cables to get INPA to detect either KL30 or KL15 (or maybe both? I can't remember). I don't recall what the fix was but I wonder if it was spoofing the value on the relevant pin? I wonder if that's what you're seeing on the first laptop?Originally posted by nextelbuddy View Post
i just downloaded and installed 1.2.1 to my other laptop and i dont have anything installed driver wise or bmw tool wise other than this DS2 tool from today. when i run it, it shows nothing is connected as i would expect.
my bmw tool laptop which is a lenovo thinkpad, is not a VM and has many things installed along with previous FTDI drivers not the ones you provided but my D CAN USB is not plugged in when that issue happens. normally it show COM1 if it is plugged in.
not a huge deal for me but i will try different scenarios and see if i can nail that one down
for now seems to be an isolated environmental related issue specific to me
- Likes 1
Leave a comment:
-
What does INPA show when you perform the same steps?Originally posted by ac427 View Post
I'm not sure if i am helping but with the latest version of the tool and nothing connected to my laptop but with FTDI drivers loaded, KL30 and KL15 are not illuminated.
However, as soon as i plugged the USB end of the cable in the COM port but without the OBDII connector plugged into the car both KL30 and KL15 illuminated.
The way that the KL30 and KL15 detection work is that they are connected on specific pins (DSR and RI) on the interface. Some interfaces have one or both of these pins simply connected to supply, so the detection is not accurate. The app uses the same approach as INPA so the behaviour should be the same. If you get a difference between the two that's where it will get interesting. I've been through the relevant code again and can't find anything that suggests a bug (Not to say there isn't one, I just can't find it if there is).
Leave a comment:
-
Yeah I'll do that and get a dedicated windows laptop too. Thank you.Originally posted by fattycharged View Post
you can buy windows license for about $10 License Tom
Sent from my iPhone using Tapatalk
Leave a comment:
-
you can buy windows license for about $10 License TomOriginally posted by 0-60motorsports View Post
Yeah that's what I thought mate. My cousin has a windows tablet, told him to bring it over and I'll download the tablet and give it a shot once the car is back.
Sent from my iPhone using Tapatalk
- Likes 1
Leave a comment:
-
I'm not sure if i am helping but with the latest version of the tool and nothing connected to my laptop but with FTDI drivers loaded, KL30 and KL15 are not illuminated.Originally posted by nextelbuddy View Post
i just downloaded and installed 1.2.1 to my other laptop and i dont have anything installed driver wise or bmw tool wise other than this DS2 tool from today. when i run it, it shows nothing is connected as i would expect.
my bmw tool laptop which is a lenovo thinkpad, is not a VM and has many things installed along with previous FTDI drivers not the ones you provided but my D CAN USB is not plugged in when that issue happens. normally it show COM1 if it is plugged in.
not a huge deal for me but i will try different scenarios and see if i can nail that one down
for now seems to be an isolated environmental related issue specific to me
However, as soon as i plugged the USB end of the cable in the COM port but without the OBDII connector plugged into the car both KL30 and KL15 illuminated.
- Likes 1
Leave a comment:
-
i just downloaded and installed 1.2.1 to my other laptop and i dont have anything installed driver wise or bmw tool wise other than this DS2 tool from today. when i run it, it shows nothing is connected as i would expect.Originally posted by karter16 View Post
Weird. No it's not. Let me investigate. Are you running in a VM?
What happens if you close and reopen the app, it persists?
Edit: I don't seem to be able to reproduce this on my test machines. Is COM3 the COM port your cable is usually on? or a different / virtual COM port?
my bmw tool laptop which is a lenovo thinkpad, is not a VM and has many things installed along with previous FTDI drivers not the ones you provided but my D CAN USB is not plugged in when that issue happens. normally it show COM1 if it is plugged in.
not a huge deal for me but i will try different scenarios and see if i can nail that one down
for now seems to be an isolated environmental related issue specific to me
- Likes 1
Leave a comment:
-
Weird. No it's not. Let me investigate. Are you running in a VM?Originally posted by nextelbuddy View Postis it normal in 1.2.1 to show KL15 ignition on when i just have the application open but no USB cable connected?
i just downloaded and installed over previous version and launched 1.2.1 but saw the status shows KL15 ignition on
What happens if you close and reopen the app, it persists?
Edit: I don't seem to be able to reproduce this on my test machines. Is COM3 the COM port your cable is usually on? or a different / virtual COM port?Last edited by karter16; 06-04-2026, 06:55 PM.
Leave a comment:
-
is it normal in 1.2.1 to show KL15 ignition on when i just have the application open but no USB cable connected?
i just downloaded and installed over previous version and launched 1.2.1 but saw the status shows KL15 ignition on
- Likes 1
Leave a comment:
-
Originally posted by ac427 View PostIs there a guide to wiring in the CSL flap motor and sensor available?
Well here is my DIY attempt at converting my wiring to OEM CSL after replacing my MSS54 with a Terra Modified MSS54HP. I have an OEM CSL Airbox with Flap and all OEM ducting etc.. Starting to untangle the mess LOL..... http://i17.photobucket.com/albums/b96/ejazsharif/DARTH%20VADER/CSL%20MAP-IAT-FLAP%20wiring/IMG_0840.jpg
- Likes 1
Leave a comment:
-
Is there a guide to wiring in the CSL flap motor and sensor available?
Leave a comment:
-
Could the tool be trying to close it when it is already closed or vice versa?Originally posted by karter16 View Post
Nah if it's working for you with tool32 then it'll be the app. There must be something else that's affecting it as well. Just a bit hard to figure out without having one myself to test with
Sent from my iPhone using Tapatalk
It sounds a lot like the throttle actuator at 100%
Leave a comment:
-
Nah if it's working for you with tool32 then it'll be the app. There must be something else that's affecting it as well. Just a bit hard to figure out without having one myself to test withOriginally posted by Cubieman View PostHmm, still having the same issue with the flap test. Not sure if it's my tune that is suppressing DTCs or what.
Sent from my iPhone using Tapatalk
Leave a comment:

Leave a comment: