The "Post Your Wheel Setup" Thread

[Tbonem3]

That's almost the correct E46 M3 set. The rears should be the 10"ET25, not 10.5" - maybe double check with seller.

If it is the 10.5", they'll still work, but I don't think a 2" stagger is ideal. 245/275 would be best imo.

[Lee_Enfield]

I'll ask this here since it's relavent.

Guy has a set of BBS CH-R for sale States will fit E46 M3, just want to confirm. My car is pretty much stock. Not looking to change anything up too much at the moment.

From his add they are:
Front: 19x8.5 et32
Rear: 19x10.5 et25

Might be a decent deal.

[Cubieman]

I like these 18" sportline 8's for the offsets/weight, but want the finish of a CSL/ZCP.
Going to start looking into painting options or possibly just buy some new ZCP's, too bad the fronts are so narrow but it's a 99% street driven vehicle so likely a non-issue.

[liam821]

Did you use any concentric hub? The wheel bore and our wheel hub size are different

Yes, I used a 72.6mm ID to 73.1mm OD hubcentric rings. They're super thin but was necessary to fix the wheel shake at 80mph.

This is what I ordered: https://www.amazon.com/gp/product/B00F3QUA6U

[PurelliCondoms]

Here’s something rare-ish most of you guys haven’t seen in awhile. Goes perfect on my car. Needs a bit more spacer in the front and rear and a tiny bit more low, but good enough for now.

Hard motorsport Centerlocks18x9 et35 265/35/18 square Hankook RS4. 12mm spacer in the rear. Needs a 20R and 12F.

[Boost]

out of curiosity, why aren't you guys with the 359Ms running 245/275?

I was more or less 50/50. A few small factors:

1. Wanted to play it safe when it came to rubbing in the front. The 359Ms are wider than the E46 ZCPs (8" vs 9" up front) and I wasn't sure how aggressive I'd be going on suspension. And my fender liners were brand new. And I hate rubbing..

2. Per Ian's tire sizing thread, the difference in circumference is marginally less (maybe like 1/4 inch iirc) between the 235/265 low pros than the 245/275 low pros.

3. The smaller rubber was cheaper and had a quicker ETA at the time

Moving forward, I might try the 245/275 (with or without +5 sidewall), or go a little lower to get rid of the bit of fender gap I have right now. Or both..

[ldmiller78]

So I had 2x LSB. Unfortunately one was totaled but here are the old and new setups

[Cubieman]

Arc8R in Brushed clear, 18x10 ET25 275/35/18 square with 12mm spacer in the rear

Nice, any close up shots? I considered these wheels, also looked into the polished finish but if I remember correctly the polished finish wheels were not offered in the same offsets as the others for some reason.

Nice wheels in any event!

[Casa de Mesa]

Those are the rims I want as well. I like the look a little better then the E46 comp rims. Been keeping an eye out for a set.

Yeah that does look pretty great.

[tnord]

out of curiosity, why aren't you guys with the 359Ms running 245/275? I have the same width/offsets and those tire sizes with no rubbing, but might not be as low. I'm thinking about upgrading wheels to TA16, or some BBS option but I do really like the design of these. There's something about the radius of the fender arches and the radius of the concavity matching up that appeals to me. I just scrolled through this whole thread and was surprised I didn't see a single TA16 setup.

Apex EC7
18x9 +31 245
18x10 (or are they 10.5? I don't remember) +25 275

[Boost]

Those are the rims I want as well. I like the look a little better then the E46 comp rims. Been keeping an eye out for a set.

I concur. Snag a set, you wont regret it

[Lee_Enfield]

No good pics but I'm running 359Ms off an E9x M3. I like the concavity.

19x9 +31 (235/35/19)
19x10 +25 (265/30/19)

Need more rubber..

If I try another setup I'd like to pick up some TEs

Those are the rims I want as well. I like the look a little better then the E46 comp rims. Been keeping an eye out for a set.

[Mtrace]

Arc8R in Brushed clear, 18x10 ET25 275/35/18 square with 12mm spacer in the rear

[nextelbuddy]

Looks great, really does.

My dude was so excited when he turned 16 and then he got a Hyundai (6 speed manual of course), lol. He is 18 now and when home from college we take turns driving the back roads in the sunshine, the best of times.

That's awesome! My little guy loves this car and can't wait to take it over when I kick the bucket 🪣🫠

[nextelbuddy]

996s

Front wheel is 9"et31. My 9"et30 arc8 needed a 5mm spacer minimum fwiw.

I barely clear with a 3mm spacer up front 😂