Cockroach Individual M3 1/13 CSL rep Bumper sourced and mockup

[samthejam]

Bruh...your road trip was like an old Top Gear episode but without the support truck!

Yeah my cross country adventures can be a bit bold.

Here is my welding my E28 strut housing to get back home after the used Hooisers sheared it at Barber.

[bigjae46]

Bruh...your road trip was like an old Top Gear episode but without the support truck!

[samthejam]

Had another DE. Car did well, blew my expectations out the water in terms of the pace it could do. The high bite front pads were fantastic, huge confidence boost. The 08s work on my E28 but they were terrible for me on this car. I am a big PFC fan, but they just didn't work for me on this car. When these 83s run out, hopefully the 11s will fill the void. I believe DTC-70s would work as well but not a fan of Hawk Pads.

A bunch of 47s with passenger and was able to squeeze out a 1:46.67.



The PB Lap:

External Video

[samthejam]

The total mileage for 2024 was 14,448 miles.

I also didn't realize that this color was so rare. So I should probably look into making it shiny for 2025.



Current Projects for 2025:

- 6 Speed Swap
- Passenger Recaro Profi
- Roll Bar and Harness
- 4 Matching SSRs
- Look into getting Hood Painted
- CSL Front Bumper
- Drive that bitch

[samthejam]

Alright so another update.

Very big update, not in terms of building the car but moreso in sharing the adventures the car has been on.

So the last update was me at MSRH, and that's where this will post will start off but it is the following weekend. It was miserable out, but a good low stress way to test the car out before heading to Road Atlanta.

MSRH is horrific in the wet, there is a 10-15 mph difference between the wet line and the dry line for corner speed. It is an ice skating ring. So there were many sideways moments, but I have done many laps here so I am comfortable in the wet.

I almost got bit here...

https://youtube.com/shorts/JCqtRzrYvLA?si=hvRimtCbGoDnNVDp

It was just cold and wet but I got a lot of laps in. Car looked like it was ready for the big trip. I put some Direzzas on it since they were on closeout and for peace of mind of new tires for the whole trip. Rear pads were paper so bought some new PFC 08s for that. Also aligned it again. This time I did stock toe for the front, I don't really like the feeling of zero toe, but the main reason was to give the tires best fighting chance for all the highway miles.

Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Anyways onto the Roadtrip. Cannonball to Atlanta, in one shot from Houston. Weren't any issues.
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Went to the Aquarium and explored downtown Georgia for a bit. jayjaya29 was nice enough to let me stay at his home and use his workshop to do a bit of trackprep. These 265 Direzzas are significantly wider than the RS4s so we needed to do some fender hammering, as the damage from previous owner wasn't giving it enough clearance.

I knew the car would blow sound at AMP, but I was able to get a couple laps. It was miserable and raining. 107db, is what I got blackflagged for.

Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

That evening I did the SAP delete and did a P/S flush as the system was pretty angry.

Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Then it was time for Road Atlanta. It did dry up after Lunch, but the morning sessions weren't wet. Morning sessions were trouble free.
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Didn't bother recording with Go Pro. My wife was able to get some external videos.

This event was sold out, so there was a lot of traffic. When it did dry out, I came over turn 3 pretty hard. My instrument cluster did not like this and started acting up all day. Would come in and out, and during one session the tach started touching the oil temp needle so I had to start short shifting. Despite this, I was able to set a new PB, however I was not able to meet my goal of a 1:39.99 here. I had multiple instances where it was showing up on predictable but ran into traffic or cluster would spazz out and distract me.

Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

By the end of the day the cluster was struggling. Braking would make it cut out and only work with dimmer at lowest setting. We still had to go to Charleston to see my wifes family I needed to fix it, but I delayed this by a day to give myself time to sort out the cluster. I put out a WTB for a cluster just in case but took it apart at Jay's that night.

I really didn't think it was fixable but luckily was something simple. Please click the Flickr link to see what it was but basically one of the Capacitors had come off the board with the pad.

Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Jay was able to repair it for me and cluster was alive again. Also tightened up the shock nut.
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Following day, Faustino and I did an impomptu run to Tail of the Dragon. My plan was to head to Charleston that night so we would just go to the Tail do one run and come back.

Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Ended up working out perfectly. We had no traffic. Cars didn't really give any trouble, besides mine the power steering had basically no assist at idle after second run.

One of my favorite pics of the car so far.

Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr


We ended up heading to Charleston at 3am since I was beat. Needed some sleep. We did Atlanta to Charleston, in one shot. I was on fumes when we got there, and first time ever filling up with 91 in my life. I've always had access to 93.

Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

At this point the power steering was crying. Checked the reservoir and yea very bad.
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Tried to do another halfass resevoir flush to bandaid it along but at this point needed a new pump.
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

I lucked out, there was a M54 X5 at a Self Service Junkyard.
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

I was able to get permission to swap the pump out in a Autozone parking lot. They said I had a hour, I was able to do it in 40 minutes.
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Parked for the night at her Dad's house.
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Rest of the trip was all touristy nothing really car related. Went to Convington, Birmingham and New Orleans.

Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Total trip mileage was about 3000~.
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr


I was having a brake shudder that was pretty bad felt like a rear rotor. I felt it on way back from Charleston. Not sure what caused it but sure enough. I believe just the Metallurgy of these cheap drilled and slotted rotors. Unfortunately I put another used set on because my friends parts car had them. We traded them some stuff for it.
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Following this finally washed the car
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

I need to fix the cracked wheel so I can have 4 matching wheels.

Also was able to find some NOS PFC 83s for it. Yes you read that right 83, can't imagine how long those have been sitting on the shelf. Threw those in on NYE. Yes I am running the pad clip.
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr
Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

Fall ‘24 Update by Kurvenkamph Motorsport, on Flickr

[samthejam]

So got the strut towers finally welded, they have been cracked since I got the car as well as the Strut brace. My friend was able to tig it in the car with everything still assembled.

Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr

Strut Brace also repaired. It was cracked clean through.
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr


I signed up for an impromptu event at MSRH, my local track. Very familiar with this place, and aren't many consequences here for most places when you push so it's great to feel a car and test it out. I was really low on rear pads, so just wanted to get one test session in. They had some portable curb things to move the apex's which in a couple spots was terrible like into Gut Check and coming out of Keyhole were the most irritating ones.

Untitled by Kurvenkamph Motorsport, on Flickr

Car is super easy to drive though, the new Hotchkis bar was a nice addition. It is at the softest setting right now, might want to stiffen it but the balance of the car is very good. Overall it is too soft so on the 265 Rs4s now it is okay but if I start running fresher Hoosier takeoffs or even RE71RS I am a bit concerned itll be a bit soft. But anyways car was boogie'ing. Annihlated my PB here I did in the E28 on Hoosiers.

Untitled by Kurvenkamph Motorsport, on Flickr

Here is a lab of the PB:

Unfortunately after that PB car bit me and the thermostat went into the water pump. So the car has been running extremely cold, which has been tough to daily drive with since it's finally getting moderately chilly here in Texas. I had a used thermostat on standby, but was debating on going the Anri 70C or motorsports thermostat. Red light of death luckily never came on caught it quick and was able to coast/ limp car into pits.

I had a friend drive me back home to grab the thermostat, as I suspected that was bad since the top hose was hot and bottom room temp. I thought the thermostat froze shut. I brought my spare used water pump as well just in case. Glad I did.

Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr


I also was lucky enough to have this which I had on hand just for emergency's.

https://nam3forum.com/forums/forum/classifieds/member-services-rentals-products/4125-m3-s54-cooling-system-hi-temp-o-ring-kits

Was able to get the car all patched up with the brand used parts and new orings and it left under its own power.

Untitled by Kurvenkamph Motorsport, on Flickr


Systems check the following day.
Untitled by Kurvenkamph Motorsport, on Flickr


So if you notice all the parts that were removed are absolutely covered in RTV (I hate RTV). Well one connection was not and I think this thermostat has been out for a long time. So when we were assembling everything, the water pump pipe stayed with the thermostat housing. We found out it cannot be assembled like this. So we got the pipe out which took quite a bit of time as it had never been seperated.

Now it's hard to say since my thermostat came out in many pieces. However my hypothesis is the monkey who was in here before and replaced the water pump (2010 date code) as well as the thermostat did not know that pipe needed to be be in the block/head first. He jammed it all together somehow, and this bunged up the thermostat. Since I got the car it had a coolant temp implausible code and then I deleted that DTC. My guess is, it has been like this for a long time but anyways all correct now.



There will be a HPDE next weekend I'll be instructing at will test car more. Then it will go on a long roadtrip and get a day of beating on at Road Atlanta the following weekend.

[samthejam]

Have you measured your ride height yet as it sits now? Sorry if I missed it.

Alignment spec is -3.5 front (no toe), -2 rear (factory toe)?

Love those SSRs!!

I keep forgetting to check this. I forget exactly what it is but I remember raising the rear because of this thread.

https://nam3forum.com/forums/forum/main-forum/e46-2001-2006/9123-e46-m3-suspension-setup-or-how-to-not-downgrade-your-car-with-suspension-mods

It is somewhere in this window but I am limited in what I can do since my fronts are at max height with this GC setup until I get taller springs but I like the height so probably won't change.

[cornerbalanced]

Have you measured your ride height yet as it sits now? Sorry if I missed it.

Alignment spec is -3.5 front (no toe), -2 rear (factory toe)?

Love those SSRs!!

[jayjaya29]

Big 3 done!

[samthejam]

Thanks George!


Untitled by Kurvenkamph Motorsport, on Flickr
Took Friday off work, after a friend offered he could help weld in the Subframe plates. I had to rent the shop space, but that's okay. Was able to align it there and everything. I also paid my friend for the labor of welding, cutting and grinding basically hot glueing the plates in and repairing any damage. Glad I did came out better than I would've. Picture of on my way there.

Untitled by Kurvenkamph Motorsport, on Flickr


Onto the pictures.
Untitled by Kurvenkamph Motorsport, on Flickr

After an hour or so

Untitled by Kurvenkamph Motorsport, on Flickr

It was time to replace the subframe bushing with AKG 75D as well as replace the cracked right rear spring arm, I had been fully relying on the stainless steel reinforcement to hold it together. Even though I was at a BMW specialist they did not have a tool that was fairly easy to remove the subframe bushings. However I brought my RTAB tool because I thought I read that would work. It didn't, but I fiddlefucked with it and made it work.

Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr

Worked like an absolute treat with the torch. No impact just a regular 3/8th ratchet. Hammered the new AKGs into their new home.
Untitled by Kurvenkamph Motorsport, on Flickr

Onto the spring arm and guibo. I sourced a brand used one.
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr

Basically where it stopped for Friday, besides having the area cleaned and inspected. We found 3 areas that were cracked.
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr



Came back Saturday morning and my friend was feeling a lot better and cranked it out.
Untitled by Kurvenkamph Motorsport, on Flickr

Welded up the cracks, and note the gas tank is still in there. Those got covered with wet towels when welded. The Reddish plates were huge so we trimmed them a bit, as I did not want to mess with dropping the tank. I did show up with it with less than a gallon, but we worked around it.

Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr

I also found a Hotchkis swaybar laying around the shop, so put that on. Was very pleased about that.
Untitled by Kurvenkamph Motorsport, on Flickr

I haven't been able to do my alignment myself on a machine in a long time, so that was a fucking treat.
Untitled by Kurvenkamph Motorsport, on Flickr

Forgot to take a pic but -3.5 camber in front, zero toe, didn't hit my camber number I wanted on RR for some reason. So it was -2.0 and -1.6, rear toe is just factory specs.

Car drives great, absolutely transformed can feel what the rear end is doing now and the front bar really helped with the softer spring rate I have up there.

Untitled by Kurvenkamph Motorsport, on Flickr

Untitled by Kurvenkamph Motorsport, on Flickr

Total time spent doing everything was 24 hours, two 12 hour days.

[George Hill]

congrats on the wedding!

[samthejam]

Ordered the Reddish subframe reinforcement and AKG 75D subframe bushings, so that is next. My suspicions of the car having a tune have been confirmed, cat deficiency always showed as not ready. No CEL yet after the headers. When we did the CSL shift setting and 105 DTC error disabled. We used Martyn's tool and Cat deficiency was greyed out. I saw this before on a friends car but it was for the burble setting, so someone has tampered with it and software won't let you touch that setting. So no idea what's on it but someone has cooked here before.

CPV valve is starting to leak but didn't have the tool or the part so that is ordered as well.

[samthejam]

As promised, only did the front rotors for now. Rear rotors still good so want to get moneys worth out of those.

Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr

Also sourced all the missing OE stuff for the battery. Little things.
Untitled by Kurvenkamph Motorsport, on Flickr

I daily drive with the PFC 08s so the brake dust is horrednous.
Untitled by Kurvenkamph Motorsport, on Flickr


Had a wedding
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr

Instead of honeymoon, decided to do headers. That was a debacle.
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr

Also did trans mounts
Untitled by Kurvenkamph Motorsport, on Flickr


Untitled by Kurvenkamph Motorsport, on Flickr

Has a really interesting exhaust note, definitely doesn't sound like the BW exhaust I have mostly heard.
Megans, stock section 1 and their street track section to the back.

https://youtube.com/shorts/YnXjFI84Etk?si=6l7yJPmnC2eBBgKs

https://youtube.com/shorts/CcqBaVtJbOI?si=8yK9JPV52NNel1r2

[Loopyspec]

Loving the build and the wrenching you're doing. I wish I was mechanically inclined as you.

[samthejam]

If you installed a messed up Oil Pump Disk spring you could end up like this:
Vanos and wheels by Kurvenkamph Motorsport, on Flickr


The spring cap fitment was already pretty horrendous but didn't want to oversand it, not to mention the fact I smashed the Vanos unit on the spring. Don't ask how. So idk what exactly caused the pistons in the disc to seize up. But anyways I had to do it again.

Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr


First go around I did the Beisan upper guide, Lang Bolts and the Oil Pump disk. I put about 300 miles on it, and then was greeted to a cam'd idle at a stoplight. Vanos codes for both intake and exhaust. Not knowing what the hell happened, I sourced a new core unit to rebuild. same day upon failure. Got SUPER lucky with that, the shop I used to work had a S54 in pieces.

Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr

This time I learned my lesson. Don't rush it at my dads and just do everything.

I actually have access to a shop behind my house, but I feel bad leaving a car there overnight in case my landlord needs the lift. In this case though, there was no point in rushing. So I took my time and worked on the car on and off in the evenings for a week. Rebuilt the new unit with Beisan Seals, got a new solenoid pack, Vanos filter, and cleaned the solenoid block. Also did the Vanos line.

Take 2:
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr

Doing the seals restored a lot of driveability with the old girl, so glad I did the seals on the second go around. Learned a lot from this ordeal. I have put about a 1000 miles on it since then, one of the break in drives was to pick up the wheels.

So like I mentioned in my first post, I used to tag along with my dad to HPDEs at Texas World Speedway. The CDI there for PDS had a E46 M3 full racecar. He was paraplegic, so he had a SMG, slicktop E46 M3 it had Grand Am Motons, Stoptech 355mm brakes front and rear, badass cage, Fulcrum Aero which had a really good front splitter, huge rear wing that tied into the floor. He was a very good driver and the car was very sorted. It was built pre 2006, so a very OG build. On the car he had SSRs, I remember the car being stored at the track and the garage had a fuck ton of wheels in there with Hoosiers.

Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr
Untitled by Kurvenkamph Motorsport, on Flickr

Long story short, when these came up on Marketplace I knew exactly where they were from. I was able to get all 10 for the same price as a set of New apex's. Biggest downside is only 4 were a matching set. One of which was cracked. The others were sets of 3s. All these are the same size. 18x9.5 ET35, yes they are old tired wheels used on a racecar with Aero and hoosiers and mismatched, but finding a nice pair of quality wheels these days for that little is hard. I also need spares since I drive the car around Houston, want to juggle sets of tires. I would like to get a set refinished to match but there are bigger fish to dry right now, the cracked one is cracked on the inner barrel so that should be no issue getting that welded. More projects for another day.

I was able to fit all 10 wheels in my M3 as well as Recaro Profi he gave me just to get it out of his shop. Missing cushions so another side quest of finding those has begun.


Here is a video of 12 year old me riding in that car on those wheels, 12 years ago.

https://vimeo.com/63381733

Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr


It would be a lot nicer if they matched, but for now this will do.

Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr

Next project will be brakes I want to do the 996 stuff but will just do the CSL/ZCP brakes for now.

Some other random pictures.
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on FlickrVanos and wheels by Kurvenkamph Motorsport, on Flickr
Vanos and wheels by Kurvenkamph Motorsport, on Flickr