Forcing OBD Readiness

[bigjae46]

Did you just just zero out the last 2 bytes or the entire string?

[andrebxp]

When are you planning on visiting an emissions testing station? Here in Maryland all emissions testing has been suspended and turned into COVID drive thru testing.

Is your SAP still listed as equipped and ready or just not equipped?

Auto repair shops are considered essential in NYS so they're still open.

SAP is listed as equipped and ready.

[eacmen]

I was able to work this out. I ended up just suppressing every single emissions related DTC and that caused all of the monitors to set to ready right away. This was a bit of a "shotgun" approach but I was tired of messing with it. You can probably get away without suppressing all of these.

For anyone that wants to do the same, suppress DTCs(decimal): 12, 13, 14, 19, 27, 36, 37, 38, 39, 40, 63, 87, 88, 90, 91, 92, 93, 127, 144, 145, 154, 170, 171, 175, 176, 178, 179, 180, 181, 214, 215, 216, 217, 218, 219, 221, 232.

I also disabled the SAP since mine is deleted: https://github.com/saildot4k/MSS54-X...dary-Air-Pump).

More info on suppressing DTCs: https://github.com/saildot4k/MSS54-X...ion-Strategies. I zeroed out the 13th byte (Method 1), but those running early MS54s might need to try one of the alternative methods.

I wouldn't recommend doing this to your main tune, but if you need to force your monitors in a pinch, this is a quick and dirty way to get it done.

When are you planning on visiting an emissions testing station? Here in Maryland all emissions testing has been suspended and turned into COVID drive thru testing.

Is your SAP still listed as equipped and ready or just not equipped?

[andrebxp]

I was able to work this out. I ended up just suppressing every single emissions related DTC and that caused all of the monitors to set to ready right away. This was a bit of a "shotgun" approach but I was tired of messing with it. You can probably get away without suppressing all of these.

For anyone that wants to do the same, suppress DTCs(decimal): 12, 13, 14, 19, 27, 36, 37, 38, 39, 40, 63, 87, 88, 90, 91, 92, 93, 127, 144, 145, 154, 170, 171, 175, 176, 178, 179, 180, 181, 214, 215, 216, 217, 218, 219, 221, 232.

I also disabled the SAP since mine is deleted: https://github.com/saildot4k/MSS54-X...dary-Air-Pump).

More info on suppressing DTCs: https://github.com/saildot4k/MSS54-X...ion-Strategies. I zeroed out the 13th byte (Method 1), but those running early MS54s might need to try one of the alternative methods.

I wouldn't recommend doing this to your main tune, but if you need to force your monitors in a pinch, this is a quick and dirty way to get it done.

[tdott]

I have not confirmed, but I found this quote:

"It has been reported that 0'ing out the entire string for the cat efficiency codes sets the monitors to ready."

[tdott]

There are 4 methods, I can't remember which one still sets readiness, I remember it being one of them, maybe someone else can confirm:

Example DTC String: AA 01 01 01 01 01 01 00 01 02 03 28 01 FF

METHOD 1: The first method to suppress a DTC, and coincidentally also the easiest, requires only a simple modification of the DTC string by replacing the 13th byte with '00':

String:AA 01 01 01 01 01 01 00 01 02 03 28 00 FF

METHOD 2: The second method is to actually zero out the entire 14-byte string:

String:00 00 00 00 00 00 00 00 00 00 00 00 00 00

METHOD 3 (untested): The third method is to perform a hybridization of the previous two by zeroing out the first and 13th bytes of the 14-byte string:

String:00 01 01 01 01 01 01 00 01 02 03 28 00 FF

METHOD 4 : The fourth method is to substitute the following string for the entirety of the original string, exactly as has been done within other OEM binaries for OEM suppressed codes:

String:00 28 28 03 02 03 02 00 01 02 03 28 00 FF

[andrebxp]

I'm sure this was covered at some point on m3F but, what is the easiest way to just force the readiness monitors to be either N/A or Ready? I have an MS54HP 2501.

I've suppressed the codes for missing hardware but I can't for the life of me get the Evap, SAP and O2 Sensor monitors to set.This is my binary if anyone wants to take a look: https://drive.google.com/open?id=1It...sZegr5v6pCMfFu


Any help would be very appreciated!