Review: Cobra Nogaro seats (uniquely street friendly fixed back bucket seat)

[Phoenix///M3]

The spg is not a street friendly seat. Doesn’t work well with with a 3 point, pita to get into/out of.

Was afraid of that being the case and Negaros possiblely being too small


Sent from my iPhone using Tapatalk

[Obioban]

Noticeable differences? Comfort / fit wise? I see the dimensions but interested in how that translates.


Sent from my iPhone using Tapatalk

The spg is not a street friendly seat. Doesn’t work well with with a 3 point, pita to get into/out of.

[Phoenix///M3]

I had the SPG XL in the M3 wagon at the same time as the Nogaros in my M3 coupe for a while.

Noticeable differences? Comfort / fit wise? I see the dimensions but interested in how that translates.


Sent from my iPhone using Tapatalk

[Obioban]

Anyone have seat time in both Negaros and Recaro Profi SPG XL?


Sent from my iPhone using Tapatalk

I had the SPG XL in the M3 wagon at the same time as the Nogaros in my M3 coupe for a while.

[Phoenix///M3]

Anyone have seat time in both Negaros and Recaro Profi SPG XL?


Sent from my iPhone using Tapatalk

[Casa de Mesa]

Got it, makes sense now. My seats arrive tomorrow, so will tackle this next week most likely.

Thanks much Cubie!

[Cubieman]

Hey Cubieman what is the 2nd pic of the wiring harness that looks like it's from a donor car?

When I bought my seat bases, I got everything, including that wiring in the 2nd pic. Is that your wiring you already have or is that just a reference pic?

I'm asking because I'm trying to see what else I might be missing that I don't have yet should I decide to do heated seats (and converting anything else I need to - seat belt receiver/pretensioners, etc.). As far as I can tell, I should have everything but I might not see the trees through the forest yet... or however that saying goes.

So that particular set of connectors/pigtails (the large ones) come up from under the carpet and then connect to the seat. The two smaller connectors connect to the back of the switch console.

The only reason I have that stuff it is a while back I put halos in my car and added a kill switch to the console (like the one you are switching out) and bought a replacement (heated) console from MpartsWW so I could always make it stock again, they also sent those pigtails. They sold it as a heated seat retrofit kit on ebay.

You should not need those pigtails for the install, however it looks like Bry5on is using them for more easily identifying what wires do what in the main seating harness, I may be wrong.

I do believe all you need is the main harness for the seat thinned down so it only does what you need, in out case, seat belts and seat heats. From there you either can build some extra wiring bits so for example an e39 seat heat plugs in or simply splice right in.

Hopefully you got more lucky with the seats you bought and they are heated so you can use that harness or even the heaters. My "seat guy" claimed they were heated so I was all excited to get the rails/harness/seat heats. As it turns out im just working away at some rusty ass seat rails so I can paint them up.

[Casa de Mesa]

Hey Cubieman what is the 2nd pic of the wiring harness that looks like it's from a donor car?

When I bought my seat bases, I got everything, including that wiring in the 2nd pic. Is that your wiring you already have or is that just a reference pic?

I'm asking because I'm trying to see what else I might be missing that I don't have yet should I decide to do heated seats (and converting anything else I need to - seat belt receiver/pretensioners, etc.). As far as I can tell, I should have everything but I might not see the trees through the forest yet... or however that saying goes.

[Cubieman]

Splicing a couple wires is (personal judgement) about 100 times simpler than stitching in elements (and I’d argue safer). With the orderable e39 elements, you don’t get hip or waist heating like with the e46 seats, but it’s about the simplest integration you can make. But the hip and waist heat hug is nice..

So I just ordered part number 3 realoem (-902/-903) crossing my fingers these are something I can use, $60 shipped for both complete harnesses.

I've also got this stuff to play with as you do. Hope I'm done save the actual seat heats and figuring out what to splice. Should make more sense once the seats are out.

[Bry5on]

I'll be interested to know how this turns out, I guess I didn't want to cut/splice but I also don't want to go nuts buying all sorts of shit I can't use/won't need.

I suppose as long as the spliced points are done correctly it's safe and its of course run through a fuse as well.

I'll probably just get the part # on my factory seats, order that (used), thin down the harness/splice and re-tape.

Splicing a couple wires is (personal judgement) about 100 times simpler than stitching in elements (and I’d argue safer). With the orderable e39 elements, you don’t get hip or waist heating like with the e46 seats, but it’s about the simplest integration you can make. But the hip and waist heat hug is nice..

[Obioban]

Do you have 1 or 2 seat heats per seat? Also, any idea of what kind of harness/heaters you got going on?

If I remember correctly you had HMS sew in E46 seat heats, they unfortunately don't do that anymore and of course the seat heats are NLA.

I'm not to worried about the sewing in of the seat heats, just want to make sure I order the right stuff as it's all so damned expensive.

I just bought some used manual heated seats and extracted the sliders, wiring harness, and heat pads.

sport seats, so 3 per seat. I think? Been a while.

[Cubieman]

I’ve been using my seat heaters every day this month. Multiple mornings in the teens 🥶

Do you have 1 or 2 seat heats per seat? Also, any idea of what kind of harness/heaters you got going on?

If I remember correctly you had HMS sew in E46 seat heats, they unfortunately don't do that anymore and of course the seat heats are NLA.

I'm not to worried about the sewing in of the seat heats, just want to make sure I order the right stuff as it's all so damned expensive.

[Cubieman]

e39 elements are electrically compatible but use different pins and plugs from the e46. You’ll need to splice or re-crimp and re-pin the connectors from an e46 donor harness. I’m deep in the aftermarket seat heating wormhole right now and have both a breakout harness and the e39 elements on the bench for diagnostics. Make sure you get positive-negative wiring correct or the buttons won’t work correctly.

I'll be interested to know how this turns out, I guess I didn't want to cut/splice but I also don't want to go nuts buying all sorts of shit I can't use/won't need.

I suppose as long as the spliced points are done correctly it's safe and its of course run through a fuse as well.

I'll probably just get the part # on my factory seats, order that (used), thin down the harness/splice and re-tape.

[Obioban]

I’ve been using my seat heaters every day this month. Multiple mornings in the teens 🥶

[Bry5on]

e39 elements are electrically compatible but use different pins and plugs from the e46. You’ll need to splice or re-crimp and re-pin the connectors from an e46 donor harness. I’m deep in the aftermarket seat heating wormhole right now and have both a breakout harness and the e39 elements on the bench for diagnostics. Make sure you get positive-negative wiring correct or the buttons won’t work correctly.