Announcement

Collapse
No announcement yet.

UPDATED: Camber issue with Vorshlag camber plates

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    UPDATED: Camber issue with Vorshlag camber plates

    I think I'm retarded. This is the new longer Vorshlag ultra complicated shaft nut thingie.

    Does this top nut need to be flush with the bearing? Because I already almost knackered the shaft threads on the otherside try to get the fucker on.

    Click image for larger version  Name:	IMG_6509.jpg Views:	290 Size:	67.1 KB ID:	502385

    EDIT:

    Ok, got the top nut issue fixed. My struts were an oddball. M3 Bilsteins are M14 with a shorter shaft, Non-M Bilsteins are M12 with a longer shaft. Mine were M14 with a longer shaft...I think that's how Vorshlag explained it.

    But now I have a camber issue.

    I ran the non-M Vorshlag plate with the TC Klines, I had maybe a .5 degree difference in camber left to right. With the new non-M Vorshlag plates and the FCM Bilstein struts, I can get -5.5 on the left side, only -3.5 on the right side. I am usually around -4 to -4.5, I think -3.5 won't be enough.

    The right side did take a hit about 19 months ago during a nasty off which damaged a control arm ball joint and the FCAB. Still was able to get both sides to about 4.25 degrees. The right side was closer to max camber but this car has always been like that.

    I also noticed the left side wheel sticks out a little more than the right side.

    Here's what I checked:

    - struts are fully seated in the kingpin
    - camber plates are on the correct side, oriented correctly, and both set to the same caster position
    - Bolt rings are correctly oriented to clear the backside of the bearing housing
    - sway bar is not binding / minimal preload
    - ride heights are set to optimize corner balance - left side is a little higher
    - visually, the left side at max camber has significantly more camber

    I'm thinking I may need to replace the knuckle. Thoughts?

    Pics are post alignment and corner balance. Toe is 0.0 on both sides.

    Left side:

    Click image for larger version  Name:	Left Camber.jpg Views:	3 Size:	84.6 KB ID:	615053
    Click image for larger version  Name:	Left Camber Plate.jpg Views:	3 Size:	102.5 KB ID:	615054
    Click image for larger version  Name:	Left Side.jpg Views:	3 Size:	127.5 KB ID:	615051

    Right Side

    Click image for larger version  Name:	Right Camber.jpg Views:	3 Size:	98.6 KB ID:	615052
    Click image for larger version  Name:	Right Camber Plate.jpg Views:	3 Size:	97.8 KB ID:	615050
    Click image for larger version  Name:	Right Side.jpg Views:	0 Size:	102.6 KB ID:	615057
    Attached Files
    Last edited by bigjae46; 11-11-2026, 06:33 AM.

    #2
    On this F80M plate, it looks pretty flush to me, but before you break anything , you might want to give them a call.

    Click image for larger version  Name:	plate.jpg Views:	0 Size:	63.3 KB ID:	505226
    Last edited by Slideways; 10-07-2026, 08:32 PM.

    Comment


      #3
      just hit it with an ugga


      Sent from my iPhone using Tapatalk

      Comment


        #4
        Originally posted by fattycharged View Post
        just hit it with an ugga


        Sent from my iPhone using Tapatalk
        Who you talking to? I always ugga dugga! lol

        Now I need to retap the threads.

        Comment


          #5
          Originally posted by Slideways View Post
          On this F80M plate, it looks pretty flush to me, but before you break anything , you might want to give them a call.

          Click image for larger version Name:	plate.jpg Views:	0 Size:	63.3 KB ID:	505226
          Fudge...I guess I need to call them. They are a PIA to deal with...I'll definitely be the moron here. But they make great camber plates.

          Comment


            #6
            didnt you check that it assembled before cranking the hell out of it??

            Comment


              #7
              Originally posted by digger View Post
              didnt you check that it assembled before cranking the hell out of it??
              ..

              Comment


                #8
                These are the FCM dampers I've been waiting on. So I got non-M PSS which I guess has a shorter stem that the M3 PSS? Not sure that makes sense because I bought non-M vorshlag plates. Either way, sent an email to Vorshlag and will call them today.


                Originally posted by digger View Post
                didnt you check that it assembled before cranking the hell out of it??
                Why would I do that? Lol

                Yeah, very wrongly assumed it would fit.

                Comment


                  #9
                  The inverted monotubes typically have less threads on the shaft/stem. So most likely yea you need different spacer and insert combo for the pillowball. I had to make some spacers for my MCS because the stem was so long.

                  I have had good luck repairing threads on shocks with just a die for any Bilsteins I have boogered threads on. I'm sure Vorshlag will hook you up, excited to see what you think of the new setup!
                  Build Thread:
                  https://nam3forum.com/forums/forum/m...-new-pb-at-msr

                  Comment


                    #10
                    I feel ya bigjae46

                    Data point: I installed some Vorshlag plates on my Cayman R (MCS coilovers). Awesome quality, but man I wish they included instructions with them. No torque specs, nothing.

                    Also, out of curiosity, how long did you have to wait to get your FCM dampers?
                    Build thread: Topaz Blue to Shark Blue​

                    Comment


                      #11
                      Originally posted by samthejam View Post
                      The inverted monotubes typically have less threads on the shaft/stem. So most likely yea you need different spacer and insert combo for the pillowball. I had to make some spacers for my MCS because the stem was so long.

                      I have had good luck repairing threads on shocks with just a die for any Bilsteins I have boogered threads on. I'm sure Vorshlag will hook you up, excited to see what you think of the new setup!
                      It wasn't too bad, I've done worse. Just ran a new nut down the threads and they cleaned up.

                      I called Vorshlag and they will take care of getting me the stuff I need. I talked to Jason who was very helpful... I think he's the #2 there?

                      Comment


                        #12
                        Originally posted by Casa de Mesa View Post
                        I feel ya bigjae46

                        Data point: I installed some Vorshlag plates on my Cayman R (MCS coilovers). Awesome quality, but man I wish they included instructions with them. No torque specs, nothing.

                        Also, out of curiosity, how long did you have to wait to get your FCM dampers?
                        100%! Awesome parts! Vorshlag is BY FAR the best option for camber plates no matter street or track. But damn...are the plates at min or max caster? I know Terry says the bolt plates last forever but don't over torque but what's the torque spec?

                        Took 10 months. I had to text him every week or every two weeks to get updates. Definitely not convenient or quick. We'll see how it performs but I definitely questioned my decision to go FCM over MCS many times over the past 10 months.

                        Comment


                          #13
                          Originally posted by bigjae46 View Post
                          I talked to Jason who was very helpful... I think he's the #2 there?
                          Yeah, Terry is the main guy, Jason is second in command.

                          Comment


                            #14
                            I had a similar issue where they didn't send the adapters in the spring perch for the MCS shafts. Guessing the help isn't as good as it used to be.

                            Comment


                              #15
                              Good news! Vorshlag is getting the bushing I need overnighted to me. Then I just use the nylock nut that came with the struts. Sounds like problem solved.

                              Originally posted by moproblems View Post
                              I had a similar issue where they didn't send the adapters in the spring perch for the MCS shafts. Guessing the help isn't as good as it used to be.
                              My case was odd. The Bilsteins I had were for a non-M. According to Vorshlag, non-Ms usually have a shorter stem and 14mm threads. M3s usually have a longer stem with 12mm threads. I guess mine had a longer M3 stem with M14 threads.

                              Comment

                              Working...
                              X