Obioban's 2005 IR/IR Coupe

[Obioban]

Your Brembos fit under a 17 inch wheel right? I think I remember you running 17s on the track.

I'd also be interested in details on the new garage. We just moved into our new build in November. We expanded the garage in depth and width, put an extra high ceiling in the 3rd bay plus extra concrete. 99% sure a 4 post will go in late this year.

The brembos fit under the specific 17 I run (not most 17s), as do the 996 calipers I’m now running. I have 17x9.5 et35s ordered that I’m REALLY hoping fit over the 996 brakes... I really dislike the et25 setup for track use.

I don’t really have any great garage ideas, beyond having it finally be large enough to not be annoyed. Open to suggestions!

[blazenXLT]

Your Brembos fit under a 17 inch wheel right? I think I remember you running 17s on the track.

I'd also be interested in details on the new garage. We just moved into our new build in November. We expanded the garage in depth and width, put an extra high ceiling in the 3rd bay plus extra concrete. 99% sure a 4 post will go in late this year.

[Obioban]

Solid feedback thanks. Any seat time on them yet? Thats where I'm anxious to know how they are

The brakes? Yes, I drove them all last year, street and track. That was the basis of the feedback above...

[Exclusivs]

I was driving on them last year. They're... 90% as good as the Brembo GT kit was. Better than stoptech or stock, and actually easier pad swaps than the brembos, but the pedal feedback isn't quite as good.

Also, they're a not insignificantly heavier setup.

But, FCP sells the wear items, sooo....

Solid feedback thanks. Any seat time on them yet? Thats where I'm anxious to know how they are

[Obioban]

Slon wall didn't arrive in time for track season? Bummer, was looking forward to hearing your thoughts on it.

Nope... been stuck in customs for a while. Not Slonik’s fault, but still sad.

[heinzboehmer]

At this point I just need to finish a wiring harness I'm setting up, set the end links on the sways, and she's ready for the year

Slon wall didn't arrive in time for track season? Bummer, was looking forward to hearing your thoughts on it.

[Obioban]

Nice updates Ian!

Looking forward to hearing your take on the retro-fit, VS real GT kit

I was driving on them last year. They're... 90% as good as the Brembo GT kit was. Better than stoptech or stock, and actually easier pad swaps than the brembos, but the pedal feedback isn't quite as good.

Also, they're a not insignificantly heavier setup.

But, FCP sells the wear items, sooo....

[Exclusivs]

Nice updates Ian!

Looking forward to hearing your take on the retro-fit, VS real GT kit

[Obioban]

Looking good, I like your brake caliper stickers!

Can you explain a bit more how you leveled your scales? Mainly, how did you shim to adjust the height and how did you set up the graduated cylinders?

Ha. The stickers have double purpose-- hide the Porsche logo and tell me the caliper temperatures :P

I have two graduated cylinders, connected by a tube at the bottom with 1/2" rubber fish tank line. I put water with food coloring (to make it easier to see) in there, and fill them both ~3/4 full. I shim under till both cylinders read the same, at which point I know they're level. I try to figure out which scale is the highest, and then use all the others to compare to that (shimming the others up). Once everything is shimmed up, I zero the scales so they don't contribute to corner weights.

As shims, I use whatever the cheapest vinyl floor tiles I could find at Home Depot were (IIRC it was like $30 for 100 of them). They're ~1mm thick, so I can get reasonable leveling, and they're slippery-- so when I raise/lower the car, it doesn't get stuck high with the camber curve, and if I, say, adjust camber, I'm not fighting the friction of the tire on the scale-- the floor tiles just slide against each other.

[S14]

Looking good, I like your brake caliper stickers!

Can you explain a bit more how you leveled your scales? Mainly, how did you shim to adjust the height and how did you set up the graduated cylinders?

[Obioban]

Good progress recently (later than I hoped, but... big undertakings this winter)...

Leveled the scales:



Installed the Fat Cats suspension, much primary colors:



Installed the final tube of the brake ducting, and confirm it fits without issue in all positions:







Confirmed I can fit a 275 Hoosier slick up front without rubbing on an et35 wheel (as that's about worst case):



Aligned and corner balanced the car:



At this point I just need to finish a wiring harness I'm setting up, set the end links on the sways, and she's ready for the year

[Obioban]

Bruh, pick up a new main board for like $15 bucks on amazon.

They’re in the trash and not coming out. It was time to move on to not junk.

[Obioban]

How do you like this? Is it a significant upgrade to the 3 and did you get the DSP option? I have the 3 now but BT and sound quality are not where I want them to be but I really like the OEM look.

I’m not the person to ask about sound quality. My speakers are connected directly to the amp inside the Avin, and all the factory wiring harness/modules/mounting brackets have been weight saved. The remaining speakers in my car were chosen by weight, not sound quality.

[Icecream]

Sadly at this point all 3 of my dremels had let out the magic smoke, so I'm on hold till a new rotary tool arrives. This time a made in Germany Proxxon tool. Can't last a shorter life than the dremel brand dremels...

Bruh, pick up a new main board for like $15 bucks on amazon.

[Icecream]

Larger screen Avin installed:

How do you like this? Is it a significant upgrade to the 3 and did you get the DSP option? I have the 3 now but BT and sound quality are not where I want them to be but I really like the OEM look.