What oil?

[Tbonem3]

What was your name on m3forum Fodi?

[Speed Monkey]

Unfortunately, these "tests" are basically meaningless for engine oil.

Basically means nothing - interesting, that’s a fairly definitive statement. Is that from the view point of a certified tribologist, a petro-chemical engineer, or one with none of these qualifications and who is a car enthusiast like most here, save for a few who have university degrees in this field. No matter where your knowledge base stands, there is some good information posted in Project Farm’s (PF) video. This detailed information is below, and PF’s data is derived from sending oil samples to a lab for analysis.

PF describes TBN as the oil’s ability to neutralize acids deposited in the oil from combustion. Like all the tables, the greater the value, the better the oil will perform.

So glancing at this lab derived information, would you buy Lucas Oil, or Amsoil based on the data below, or is it like you say, “...”tests” are basically meaningless...”. Whether you like data or not, I do like data, and the data below indicates the better performing oils would be Redline, Amsoil and Pennzoil.

[Dash1]

I stated my point clearly and you quoted it.

It's kinda stupid to design oil around additives but hey, people like adding additives for piece of mind when they can just buy good oil.
I should've said "better" to be less absolute. It's all trash we must sift through. What makes an oil better would be the MOS2 included in the base oil without the additives. Everything else is pretty much the same. I believe it makes it more shear resistant and is just a lubricant that sticks to the metal surfaces. I don't claim to be an expert, I'm just a oil keyboard warrior with an opinion.
Seriously though, I'm done with Liquimoly. It wasn't all the oil's fault I had a piston exploded into at least 100 pieces, but it just left a bad taste in my mouth. I also used Ceratec. Still went boom. I'm sure my car will be fine without it. I didn't notice any smooth coating on anything and it was in there for 5,000 miles. I'm just not a believer. They have really good marketing. They have a potent engine flush.

If your bearings went out after 5k then I'm more inclined to think that there was an improper install. Of course, there's no way to prove it and you're being biased toward an oil that many others are using with no complications and without using additional additives.

[ViN]

I am using Castro Supercar 10/60. The previous change I did switch to Pennzoil 10/60 and I don't know whether it was real or perceived, but the car didn't seem to run as well and I thought there was a bit more noise (rattling sound) coming from the warmup. I have been very pleased having switched back.

[IamFODI]

That’s my dilemma every oil service. Do I keep with the liqui moly which I put 120k hard redlined daily miles on (changed my bearings at 185k, and they looked great) which burns no oil. Or...do I go with the shell. I’m in an if it ain’t broke don’t fix it kind of situation.

As a BMW 10W-60 user currently... If I had your history of success with Liqui Moly, I'd stick with it.

Only use castrol edge 10w60 or shell helix racing 10w60. The rest (liqui moly bmw 10w60 etc) do no have the additives needed.

Not to necessarily defend Liqui Moly vs. Castrol or Shell, but what's important here isn't the additives; it's the performance. Formulations are complex and it's entirely possible to have similar performance with a different additive package.

I've spent hours with tribologists of several oil testing companies and my takeaway each time is: 10w60 is 10w60 and 10w40 is 10w40 REGARDLESS of brand!

If they said that, I'd bet good money they were oversimplifying on purpose and/or speaking within a very specific context -- OR they weren't actually tribologists (maybe they were some other kind of professional).

AFAIK, the truth is this (maybe this is what they meant):

1. Viscosity -- not just the viscosity grade, but the actual viscosity in service -- is generally considered the most important feature of a lubricant.
2. Most of the time, there won't be night-and-day differences among oils within a viscosity grade.
3. If you look at two oils with the same performance classification, they will perform similarly.

Additives can make a big difference, though. Deposit control, anti-wear performance, friction modification, catalytic converter poisoning... Lots of things.

Blackstone will tell you that we S54 guys are the lionshare of their independent customers so they have a huge database on the results of the oils we run. MOST of us, whose oil they test, use 10w60, but they also have a healthy number of those owners who DON'T. I asked what other weights they see allot and they said: 0w40, 5w40 and 10w40. I asked; "do you see any difference in those weight oils versus 10w60 in how those alternate weights test out?" and they say NO.

Agree completely with the overall message, i.e. that there's no evidence that screwing around with viscosity will make the S54 or any other engine blow up or last much longer. Just wanted to add that what Blackstone sees isn't actually wear. It's "wear metal" numbers on an oil analysis, which aren't the same thing.

I've been told several times when talking to Redline Oil engineers who know the S54s well, that 10W60 was 'not the original factory fill' but it was a 'bandaid' and said; IF 10w60 was the fix for thin rod bearings then why do so many engines running it still spin their rod bearings(???)

👍

Oh and BMW oil = Penzoil

Shell owns Pennzoil (and Quaker State).

Lead and molybendum are both lubricants.... why would you want less? What defines better?

Lead isn't a lubricant. In this engine it's a wear metal.

Moly-based friction modifiers are good, though like any component of a lubricant, they do have downsides (e.g. ash, competition with anti-wear and detergent molecules).

Found this guy on who tests pretty much every oil ever made. Ravenol 10w-60 performed exceptionally well. His spreadsheets listed under the video are pretty interesting.

Amsoil wins? Who da thunk it... Penzoil/Twin Power had a respectable showing. Motul and Liqui Moly, not such a good showing, at least when it comes to 5w-30 weight oil specifically. Though 5w-30 is not 10w-60 oil, I would say this is at the very least, it’s a window, or indicator on how a manufacturer’s oil will perform on a different grade oil.

Unfortunately, these "tests" are basically meaningless for engine oil.

[Obioban]

Hmm. Saturday I put TWS in the M3 coupe, but then I put BMW/Shell 10w-60 in the M3 wagon and M5. Hard to know which way my vote falls in the era of FCP

[TexaZ3]

LM 10w60 in my E46, E39, and E63
BMW 5w30 in my E36 and M Coupe.

[Slideways]

I think terra posted this before on M3F, but the MSDS of BMW TwinPower 10W60 and Shell Helix 10W60 is the same. Definitely looks like the same product.

[SliM3]

Not recommended for stock obviously, but Valvoline VR1 Racing 20w50 full synthetic.

[Feffman]

Here's a JPEG conversion of my 10W-60 synthetic oil Excel spreadsheet with manufacturer published test numbers for as many synthetic oils as I could track down. I hope this helps. I'm happy to e-mail the Excel sheet to anyone.

Feff

[Arith2]

Many engines have spun bearings while using Castrol so I'm not sure what your point is.

I stated my point clearly and you quoted it.

It's kinda stupid to design oil around additives but hey, people like adding additives for piece of mind when they can just buy good oil.
I should've said "better" to be less absolute. It's all trash we must sift through. What makes an oil better would be the MOS2 included in the base oil without the additives. Everything else is pretty much the same. I believe it makes it more shear resistant and is just a lubricant that sticks to the metal surfaces. I don't claim to be an expert, I'm just a oil keyboard warrior with an opinion.
Seriously though, I'm done with Liquimoly. It wasn't all the oil's fault I had a piston exploded into at least 100 pieces, but it just left a bad taste in my mouth. I also used Ceratec. Still went boom. I'm sure my car will be fine without it. I didn't notice any smooth coating on anything and it was in there for 5,000 miles. I'm just not a believer. They have really good marketing. They have a potent engine flush.

[Dash1]

Liquimoly is just trash oil. My engine DID spin a bearing while using it. Ceratec probably doesn't work very well either. It's kinda stupid to design oil around additves but hey, people like adding additives for piece of mind when they can just buy good oil.

Many engines have spun bearings while using Castrol so I'm not sure what your point is.

[Speed Monkey]

Amsoil wins? Who da thunk it... Penzoil/Twin Power had a respectable showing. Motul and Liqui Moly, not such a good showing, at least when it comes to 5w-30 weight oil specifically. Though 5w-30 is not 10w-60 oil, I would say this is at the very least, it’s a window, or indicator on how a manufacturer’s oil will perform on a different grade oil. For me, I’ll stick with what the BMW Parts Dept. sells over the counter.

[Andy2424]

Helix Ultra Racing 10W-60

[Zekarus]

Lol Motul 8100 10W-60.

+1