Right - that's what everyone says, was just curious after he scanned headers and ran it through any flow visualizations if anything even remotely popped up. Would be great to just see it as a visualization.
Announcement
Collapse
No announcement yet.
S54 Header Design talk
Collapse
X
-
Right, nothing to see. The number is so small you won't "see" anything. Put .119 vs .118 into a graph, see anything?Originally posted by davidinnyc View PostRight - that's what everyone says, was just curious after he scanned headers and ran it through any flow visualizations if anything even remotely popped up. Would be great to just see it as a visualization.
Comment
-
Jesus Christ, I'm just asking for a visual if he had any done? It's not like I don't believe this to be the case, I'm just asking. Goodness gracious.Originally posted by 332 View Post
Right, nothing to see. The number is so small you won't "see" anything. Put .00000119 vs .00000118 into a graph, see anything?Last edited by davidinnyc; 11-04-2026, 11:21 AM.
- Likes 3
Comment
-
I don't know how else to say, the difference is so small. Their isn't a way to give you a visual, that I know of. Most people go with the standard tools of measurement. Back pressure, HP gain/loss, EGT, you wont find (see) anything significant. This horse is deadOriginally posted by davidinnyc View Post
Jesus Christ, I'm just asking for a visual? It's not like I don't believe this to be the case, I'm just asking. Goodness gracious.
Comment
-
Honestly, I just might be haha.Originally posted by digger View Post
you probably mean a spike which are commonly used with non merge collectors that use parallel pipes and a formed merge rather than pipe merging at an angle
2006 E46 M3 Interlagos Blue ZCP Slicktop "CS"
Comment
-
So I decided to have a go at this... This is what I was able to come up with. I used the engine scan from this GIT, a proprietary E46 Chassis and carrier scan that the owner shared with me, and a bunch of AI.
The primary length spread is 1.6mm with a 4 stage design so it looks fairly good for the first shot. The flanges are still from the Megan Racing header as takeover so those still need work. The ends are roughly the same as OEM, but with a 63,5mm pipe.
What I still need to check is reinforcement plate fit. I only had an estimation that I placed on the chassis, which it clears.
And I need to countercheck with the supersprint oversize section 1, ideally I want to make it mate to this...
2002 E46 M3 TiAg Coupé >> full tracktool conversion @m346gt
2000 986 Boxster S >> ice cream getter
Past: E46 330Ci, 944S2, 996 C4S
- Likes 3
Comment
-
Ask and you shall receive - PM inbound.Originally posted by Altaran View PostSo I decided to have a go at this... This is what I was able to come up with. I used the engine scan from this GIT, a proprietary E46 Chassis and carrier scan that the owner shared with me, and a bunch of AI.
The primary length spread is 1.6mm with a 4 stage design so it looks fairly good for the first shot. The flanges are still from the Megan Racing header as takeover so those still need work. The ends are roughly the same as OEM, but with a 63,5mm pipe.
What I still need to check is reinforcement plate fit. I only had an estimation that I placed on the chassis, which it clears.
And I need to countercheck with the supersprint oversize section 1, ideally I want to make it mate to this...
‘02 332iT / 6 | ‘70 Jaguar XJ6 electric conversion
- Likes 2
Comment
-
Certainly looks the part, will those clear the headshields and what not on the top side?Originally posted by Altaran View Post
'09 HP2S, '12 R12GSA, '00 Black 323iT, '02 Alpine 325iT (Track Wagon), '02 Alpine 330iT
Instagram @HillPerformanceBimmers
Email to [email protected]
Comment
-
Unlikely. I don't use the factory heatshields above the headers, since my current headers have coating and thermal insulation. Any header that has a bend upward is likely incompatible with factory shielding.Originally posted by George Hill View Post
Certainly looks the part, will those clear the headshields and what not on the top side?2002 E46 M3 TiAg Coupé >> full tracktool conversion @m346gt
2000 986 Boxster S >> ice cream getter
Past: E46 330Ci, 944S2, 996 C4S
- Likes 1
Comment
-
Can you actually assemble and weld those? It looks like they are trapped together. I suppose if you're printing them, you may only need to weld on flanges.2003.5 SG/Grey
https://www.talcottmfg.com/blog
Comment
-
You should be able to squeeze Bank on through bank 2, its just cylinder 6 goes around. I'm also still working on them. Generally they still have too many parts, which will make them expensive to manufacture.Originally posted by discoelk View PostCan you actually assemble and weld those? It looks like they are trapped together. I suppose if you're printing them, you may only need to weld on flanges.
I also need to get more detailed on the collector. I don't think you can get any 3in1 made from inconel off the shelf, which is what i want to make them out of.2002 E46 M3 TiAg Coupé >> full tracktool conversion @m346gt
2000 986 Boxster S >> ice cream getter
Past: E46 330Ci, 944S2, 996 C4S
Comment
-
Altaran you inspired me. I pointed Grok Bot at my CAD models for a few hours today and I've now got all clearances totally resolved (including *all* heat shields), 590 +/-1mm runners, secondaries within 10mm, single step at 290mm from 38mm ID to 42mm ID and an AI-designed first collector iteration. The bot is chugging on a full length 7-10 degreeish merge collector replacement now.
What a world.
In process progress updates:
First iteration before corrections:
Second iteration, including a collector:
Last edited by Bry5on; 11-12-2026, 08:07 PM.‘02 332iT / 6 | ‘70 Jaguar XJ6 electric conversion
- Likes 3
Comment
-
Are we getting....Bryson headers too now?Originally posted by Bry5on View PostAltaran you inspired me. I pointed Grok Bot at my CAD models for a few hours today and I've now got all clearances totally resolved (including *all* heat shields), 590 +/-1mm runners, secondaries within 10mm, single step at 290mm from 38mm ID to 42mm ID and an AI-designed first collector iteration. The bot is chugging on a full length 7-10 degreeish merge collector replacement now.
What a world.
In process progress updates:
First iteration before corrections:
Second iteration, including a collector:
| 06 6 Speed Vert - JB on Cinnamon|Beisan|ACL RB's|ST Sway Bar|3.91|Bi-LED| TMS CSL Box|Megan headers|H.T.E Tune|Bryson Air Inlet|550 Injectors|OEM Section 1, 2, 3|200 Cell Cats|OEM SSK|Bilstein B12|712 yellow tag

- Likes 1
Comment

Comment