Not a wagon thing but it sorta counts - wired a gauge.s in to the Jag to display all the stuff hidden on the CAN bus since the car only has so many gauges. Yes the fuel gauge and tach do work for SOC and battery current (tach-ammeter) respectively.
Announcement
Collapse
No announcement yet.
Black & Tan 332iT
Collapse
X
-
Sure! In comparison to the Jag, the wagon is quite close to stock. This week the Jag got some additional attention too. I did some PCBA work (swapping resistors to get thermistor curves right), wiring (Gauge.S and switching a constant 12V drain to a switched 12V), plus lots of software. I had to add a whole lot of data to the CAN bus for Gauge.s, I had to write software to handle that 12V hot -> ignition change, a new WiFi dashboard for live data viewing that's more comprehensive than gauge.s, and with the help of Grok and about 4 prompts, built the best datalog analysis tool I've ever used - feel free to use it here, none of the data goes to a server, it all stays local until you refresh the page: https://bry5on-datalog.grok.meOriginally posted by Keith_MN View PostRequest to see the Jag! Can't say I've ever seen pics, just the sig line which has always caught my eye.
Here's the primary viewer, highlighting that I had some brief second gear wheelspin on the right rear (wagon log). Crazy how easy it is to see in the datalog, and how it shows up in the individual wheel, vs speed, vs rpm traces (also EGT?):
And a highly chaotic plot showing more you can see zoomed out over a whole log:
And in the jag, since I have current and voltage, I can actually calculate drivetrain power. And since I have power and output shaft rpm, I can calculate torque. So I decided to add another page to the datalog viewer that automatically generates power/torque dyno plots.
And since I'd done that, I had to make it compatible with the wagon for monitoring other things, like this log which had extra fuel above 7300rpm WOT:
Here's that live jag dashboard: (notably pre-resistor work)
Alright, now that we're past all that, photos of the jag as promised:
Last edited by Bry5on; 09-28-2026, 10:00 PM.‘02 332iT / 6 | ‘70 Jaguar XJ6 electric conversion
- Likes 7
Comment
-
Honestly that’s one of my favorite things. Seeing an angry EV driver that a gas car is hogging an EV spot, then seeing the look on their face when they see it plugged in.Originally posted by Keith_MN View PostCool!! Always had a soft spot for Jaguars. I can't imagine all the double takes in the EV parking spots.
When it’s not plugged in, it’s purposely impossible to tell it’s not an EV. You charge it under the original fuel filler and it even has fake tailpipes (the bike rack mount attach points). Everything electric is completely hidden and the original shifter, pedals and gauges still control the car. And all the trunk space is still there.
‘02 332iT / 6 | ‘70 Jaguar XJ6 electric conversion
- Likes 3
Comment
-
Alright, let's finally wrap this up.
EthanolTurbo is parting out an M3 cabrio and graciously donated the last of the missing parts to get this car road worthy again (it's been a while!). I got a box full of M3 evap hardware, the cover and a couple M3 specific heat shields. I also snagged the old metal driveshaft that I'd pulled off the car to swap out with the carbon driveshaft that I dropped several weeks back. The goods:
Before we get to the work, I did do one longer drive to heat the exhaust up and once again the math wins. I'd calculated that I need a full inch of space for exhaust growth (more for a track day) and after a long not aggressive drive, I consumed all of that 5/8" gap that we had to the heat shield
Trimmed it a bit and we'll see what the next weakest link is when it hits.
First, the evap lines can all be done with the subframe in-situ fortunately, also with the wheel still on the car if you're a masochist like me.
Now that we've got the evap system in, we can locate the fasteners for the evap cover and heat shield. Then we get to use George Hill 's sweet riv-stud tool with factory BMW coarse threaded studs. And behold:
Then I pulled the carbon driveshaft out, replaced the nose bushing at the transmission output flange and slapped the old driveshaft in. I'm happy to report that I can't detect any change from carbon back to the steel driveshaft, and the nose bushing seems to have corrected the 60-65mph shaking I was feeling before. Whew.
With that in, buttoned the exhaust back up, changed the royal purple transmission fluid that it shipped with to Motul 75W-80 GL4 and took it for a spin. It's properly an M3 from this view now.
And for some bonus points, the F10 535i shifter damper (25-11-7-596-098) showed up. The trans fluid change definitely helped with shifting a bit, but there's still more of that two-stage notch shift than I'd like, so let's keep the party going. It ships with a pre-installed pretty clever tool that cams over to snap this thing in place:
You can see in that photo that even in neutral we're now getting pretty close to the shifter foam, so a whole lot of that had to go
Now that we've got the clearance, another test drive notes some additional improvement, but we're still not at the smoothness I'm after. Next up I'll be trying the weighted tall shift knob and if that still comes up a little shy, I have an idea that involves 3D printing stainless steel, so stay tuned.
Now that we've wrapped up the quad exhaust saga, I want to say that this is overall one of the coolest project I've done. Not because of the car or the results, but because of the number of people in the community who really pitched in to make it happen. First of all George, who feels more like my partner in crime at this point, for ideas, scans, several test fits, tools, overnight shipping parts, and more things I'm blanking on. Then a huge shout bigjae46 for pulling a mold of an M3 trunk floor and actually making a carbon floor from scratch and getting it all the way out to me in CA (sorry we didn't connect in TX man!). And finally EthanolTurbo who tore down a car and grabbed all the M3 specific hard to source big parts that I needed to finish the job. And not to forget heinzboehmer who flew down to visit from the bay and packed extra exhaust hangers for me (from the original quad exhaust that was destined for this car a couple years ago, not the one that got installed). So yes, I'm super grateful for everyone's help, and this was just really fun to tap into some great folks in the community to see this all come together the way it did. You guys rock.Last edited by Bry5on; 10-14-2026, 04:44 PM.‘02 332iT / 6 | ‘70 Jaguar XJ6 electric conversion
- Likes 11
Comment
-
Little mini update. I’m after a tall, heavy, lighted single piece e46 M3 shift knob + boot. That doesn’t exist, so we’re gonna have to make it exist.
Well, spent some dough on a tall weighted factory shift knob to reverse engineer it. What I learned is pretty simple! The weighted knob uses the same molding as the lighted part, but replaces the lighted ring and cover with a steel mass that drops and screws in.
Removal is pretty easy - pop the cover off (be careful with the black paint so you don’t scuff it like me), unscrew the T20 fastener, then jam an M6 bolt into the steel insert and pull. This is what you get:
Here’s the lighted part, plus a conversion of the lighted tall knob+boot into a weighted tall knob+boot.
The weighted knob smooths the two-stage shift action some more, though I’d love it if the knob were 15mm higher. I tried a couple placements and found that to be the ideal balance of throw and height for me. I may do more on the height later, but we’ll see.
So this weight conflicts with the lighted insert and, though I’d rather have the weight than the light, we’re after all the cake here. So I ordered some lead shot to stuff into the knob below the lighted ring. I’ll report back if I can get 80-90g of material in there and still leave enough room for the light element. Wish me luck.Last edited by Bry5on; 10-21-2026, 09:59 PM.‘02 332iT / 6 | ‘70 Jaguar XJ6 electric conversion
- Likes 2
Comment
-
Success! A #9 lead shot and RTV slurry packed in the lighted shift knob nets us - exactly 83g of extra weight. The process here was a bit of a mess and honestly, I think if I were to attempt this again I'd probably just ditch the lighting. But we've proven that it's possible, which is fun.
Original lighted knob weight, 160g
Kapton tape for insulation
The slurry
Post-slurry weight, 243g (+83)
And because I was curious, I had to scan, model and quote the weighted insert for 316L metal 3D printing
Only $50 to get the insert printed and convert your shift knob to a weighted one! Beats Spending $170 on a new knob, plus it's a little heavier at ~100g for 316L.
Attached FilesLast edited by Bry5on; 10-22-2026, 06:51 PM.‘02 332iT / 6 | ‘70 Jaguar XJ6 electric conversion
- Likes 3
Comment
-
Designed my first PCBA tonight - a 28 x 33mm board that takes the e90 ground-shifted mirror signal, references that signal back to chassis ground, and adds a 12v turn on voltage to enable dimming at a certain voltage (0.3V in my initial schematic). This also allows the mirror heating circuit to be reconnected, and the mirror dimming will use the ground from the higher current capable mirror heating, minimizing the number of wires that need to be passed to the dimming mirrors.
TLDR: e90 auto-dimming will work just like stock in the e46 M3 mirrors
This week I'll test a breadboard version of this circuit before placing orders for the PCB version.
‘02 332iT / 6 | ‘70 Jaguar XJ6 electric conversion
- Likes 5
Comment

Comment